ETA-2834 w/o date in fake-rolex case.

Remove the cyclop (put it into Acetone)

Sapphire Crystal,

Ceramics bezel Insert, Scrow-in back/crown.

View more

ここは小樽運河のはずれです。毎日小樽運河にはたくさんの観光客がやって来ますが、ここまで来る人はあまりいません。たいていの人は観光バスがとまるあたりで記念写真を撮って、後はその辺の店でショッピングです。でも僕は小樽に来ると必ずここにやって来ます。この日も寒くてどうしようかと迷いましたが、結局来てしまいました。何故か？　それはこの場所に、よそ行きではない小樽の風景があるからです・・・・。

Then spread epoxy all around the rim of the barrel, making sure to seal the entire thing in place, then set it aside to let it dry.

View more

Taken Feb-2005 before the new Bus Station building work got under way

Lisa's R3000 laptop had the power plug stop working. It required disassembling the entire thing to install another or use the expansion port on the side for power. Commercial cables for that are $130-$220 and hard to find so I used this homemade fix I found on tomshardware.com forum using an old pci card I cut up, a $3.50 plug from radio shack and part of an old battery holder. Works surprisingly well, if I say so myself. I wish I could have hid the wires for a cleaner look but it works and saved the laptop.

From first glance I knew I wanted to get this. But the gap on the canopy was unacceptable! The other mods were just my preference. Plus I added a crew.

Here's the stock FireFly.

Step 1: Remove all screws from the case, make note of the 3 screws that are different front the others, they go in the stock. You do NOT need to remove the two screws in the cocking lever, that will come out all on its own without removing the screws.

There should be a total of 20 screws including the one on the battery cover.

Canon 5DmkII Sigma fiseye 16mm FD to EF conversion

not really an "elegant" solution but it works fine.... I'll see if I can find a better solution

Side by side comparison of the modified PT EOS taillight and a Planet Bike Superflash.

The new LED is a Luxeon III red-orange, rated for 190 lumens at 1.4A - should be good for about 40 lumens at the normal EOS max power (300mA).

The superflash has a tighter beam, but the EOS seems to be putting out a lot more light (1w on the EOS vs .5w on the superflash). The PT EOS also has better water seals, and you can set it for low and medium brightness, as well as flashing), making it a lot more durable/versatile as a bike light.

Step 8 bushings and lateral motion

Houston Texas One RELIANT CENTER Park Tattoo & Body Art Expo convention Me watching artist do their thing Tattooing people September 17 2011 Ink tattoos body modification Art Fade machine needle

The foot design in the Exosuit was ok, but I found that it was not nearly as stable as I would have cared for. With the addition of the big fuel tank/Jetpack, the extra weight caused it to be even more unstable. I extended the feet back by 2 studs. I also widened the feet with a small bracket and tile underneath. After taking this picture I replaced the 1x1 tiles with a cheese slope.

Modified bars for Top Bar hive after bees began to build across multiple bars.

This vertical steam engine once drove the air handling unit at Wilson Jr. High. The A frame remains and the piston head was removed. It has been retrofitted to be belt driven by an electric motor. This is an interesting modification of a steam engine and not too many modifications like this still exist.

modification to arduino to allow burning other chips via the six pin header

Vixen ADM 7" saddle and base for StarSense camera is ready to be used.

Tuning smart 698 cc 110 bhp

Head Modification Contest

Contestants were required to do a faceup based on the theme of PNW BJD Expo 2016: BJD Comic-Con

The wires for the auto mode sensor were removed and replaced with a 47k ohm resistor. This converted all the auto (color) settings to a 1/8th manual power setting.

That will keep it running.

Contour HD battery movement modification, using piece of nylon banding / woven plastic package strapping.

The texture and rigidity yet flexibility seems to be perfect to jam the battery and stop it moving.