A construction barge builds a wall along the L-40 Levee in the Arthur R. Marshall Loxahatchee National Wildlife Refuge. Modifications to the levee are part of the creation of the Fran Reich Preserve (Site 1 Impoundment) that will capture and store water normally discharged through the Hillsboro Canal.

The unedited cut

From 10th to 31th October

- New Necklace

Resizer inside, possible to delete it !

PS: sim limited in script ( 50)

Taxi: maps.secondlife.com/secondlife/Metropolis/139/127/49

Mod ini saya yang buat (C) Arvendo Mahardika

I could not get the Tee to slide into the chassis, so I removed 0.060" from the top 45 angle. I do not know if I misread a dimension or what, but I did not want to disassemble the frame to insert the Tee. I checked my 3D model first, and there is still 0.103" of material between the steam inlet and the relieved angle.

Filmor box camera, modified to pinhole cam

Custom IBook I'm working on. Custom Black Paintjob on the inside of the clear plastic/acrylic casing, apple logos stripped out and backlit.... inside shielding removed so when the case is open the inside is see through, so you can see the inside electronics... Upgraded Hardrive, ram, soon to be overclocked and fedora core 7 linux installed.

Added 1" and counter balance to rudder and elevator.

Landtank Seat Modification for FZJ80 Land Cruiser. Add an extra 2" of leg room. Blogged here

Showing off new and improved album art at the Record Modification table!

Modifications:

Wheels: Rennen R8 X-Treme Concave

Finish: Brushed w/ Color Matched Sophisto Grey Windows & Registers

Size: 21x9.0 | 21x10.5"

Tires: Michelin Pilot Super Sport

(F) 255/30/21

(R) 295/25/21

Suspension: AC Schnitzer Lowering Springs

Slight modifications to the bulkhead required

holga lens modified to fit a 4x5 camera

Camouflaged Yaris

I figured that since everyone else in the world has made a variation or upgrade on the m4/m16, i would too. I took the m16a4 bolt, 20" barel, m4 birdcage flash hider, then suped it up with various stuff.

Use a small section of a hack saw to cut these slots in the two posts located by the DC out cable.

The two main problems to address are the locator pins on the front of each runner plus the angle of the metal where the floor bolts go through. The locator pin comes off easily with a hacksaw. Three of the angle tabs can also be easily bent flat by sticking them in a vice and slowly easing them into shape using the length of the runners as a nice lever.

Craziest Car Modifications - Photos 14

www.carpicgallery.com/most-craziest-car-modifications/cra...

with silencer and bigger ammo clip.

my first BA mod.

Simple yet effective. All boomfunctions are available at the same time.

The texture design worked out more uniform by changing the design of the center support walls.

This is a stop-motion video I made while painting a pair of Skechers Sweets shoes.

This is a picture from my propane smoker's user manual. My smoker does not have the side dampers as this picture shows, and this is the only picture in the entire manual that shows side dampers.

Upon further research, other, more expensive versions of my smoker have these side dampers, which is probably why this graphic has the side dampers visible (reused graphic).

I'm having a very difficult time getting an internal temperature below 250 degrees in my smoker, 180-200 being optimal for things like brisket and seafood. My plan is to buy or otherwise obtain two damper covers, drill some holes, and install the dampers as shown in this picture on my smoker.

Theoretically, this will allow cooler outside air to mix with the hot air and smoke between the fire and the meat, keeping the fire hot (and the wood smoking) while keep the meat from cooking too quickly.

Some older AI images modified with new Photoshop beta. Borders were expanded and then auto filled by Photoshop. A whole new world.

Pins 16 and 2 are both strapped to +5V. This mod separates pin 16 from pin 2, and the wire brings +5V back, to power the multiplexor. Note that the solder (and pin remnants) have been removed from the pass-through hole. Since this hole connects through to pin 2, it will be used to take an the address line through from underneath.

Deep red dichro on trans red backs, made by Frozenfire on Etsy.

My new tattoo.

Extension on the side is very stable and prevents accidental operation of the right side buttons. The extension also makes the camera feel bigger and more comfortable during pod or handheld operation. Discussion at www.flickr.com/groups/2082775@N20/discuss/72157635072289891/

Men's Bathroom, Target @ Steelyard Commons. See: Before

Hand trolley modified as bike trailer?

I guess the plastic container bucketing the seat acts as a mudguard? (there's potential for some more storage there - but this owner had completely cut away the front - possibly to allow pedalling!)

Mod ini saya yang buat (C) Arvendo Mahardika

Source: livinghistories.newcastle.edu.au/nodes/view/29837

This photograph was taken by Brian R Andrews of Killingworth, NSW. Brian worked for 20 years as a Draftsman for Coal & Allied Industries Limited. This photograph is part of Brian's private collection. Brian has kindly given Cultural Collections at the University of Newcastle, NSW, Australia, access to his collection and allowed us to publish the images.

If you wish to reproduce the image, you must obtain permission by contacting Cultural Collections at the University of Newcastle, NSW, Australia.

Please contact Cultural Collections at the University of Newcastle, NSW, Australia, if you are the subject of the image, or know the subject of the image, and have cultural or other reservations about the image being displayed on this website and would like to discuss this with us.

If you would like to comment on the photograph, please contact Cultural Collections at the University of Newcastle, NSW, Australia, or leave a comment.

This photograph, like the majority of the 50,000+ photos in our Flickr site was scanned by a volunteer. When we have sufficient funds in the Vera Deacon Regional History Fund, we are able to give these wonderful people some paid employment. If you would care to make a small donation to this fund, please see libguides.newcastle.edu.au/benefactors/new for more information and a link to the donation form.

modification ears (lobes removed transitions glued), made make-up.

Details of the modification of a Stellarvue AT1010 NightHawk for solar observing at hydrogen alpha wavelength.

This view shows the adapter that slides on (it's a really tight press-fit) over the NightHawk's 80mm F6 achromatic objective after removal of the dewshield.