View allAll Photos Tagged Manufacturing_process
SHAFTER, CA – Saturday August 30th 2008 at approximately 12:48 P.M., a call was received by the Kern County Fire Department for a structure fire in the 500 block of Shafter Ave, in Shafter. Approximately 40 Kern County Firefighters responded to the incident. As the first Battalion Chief arrived a third alarm was called for, this involved a total of 2 Ladder Trucks, 7 Engines, 3 Battalion Chiefs, 1 Deputy Chief. Also, Hazmat 66, Air Van 61 and Water Tender 51, along with various support and safety personnel.
As the first fire engine from Shafter left the station the crew reported a large column of black smoke and requested a full structure response. Upon arrival, crews were faced with liquid petroleum gas tanks (LPG) on fire, also a large amount of stored roofing and building paper materials were becoming involved, these products are used in the manufacturing process and are stored outside and at the rear of the property. The heat produced by the fire caused the adjacent steel clad warehouse building to become threatened. A second alarm was requested. Fire crews made an initial attack on the exterior fire. As more fire crews arrived an internal attack of the fire was made and to ensure that no body was inside the building. Fire crews are continuing to fight this fire. The cause of the fire is undetermined at this time.
via Tumblr bit.ly/191xrWb
Custom Orthotics For Flat Feet
Flat Feet? No Problem with Custom Foot Orthotics
If you have flat feet, you know that this can contribute to problems. Because the entire sole of the foot comes into contact with the floor when standing, this can result in improper alignment of your legs. This can cause pain in your ankles as well as your knees. Flat feet are often caused when arches do not develop at an early age, typically during childhood. This can also be caused by an injury and is sometimes due to aging.
Is there a Solution for Flat Feet?
Foot orthotics for flat feet can be a relief for those who suffer from this condition. This can help relieve the aches that are experienced in the arches of the feet. Caused by the over-pronation or rolling of the ankle, this pain can be debilitating and it can also result in further injury to the feet over time.
Custom made orthotics that can be inserted into your shoes can help. They are custom fitted to your feet and have provided relief for many people. Choosing the type that is made by a method of molding cork, leather and ethylene vinyl acetate (EVA) will provide the shock absorption and the comfort needed to relieve pain. The othotics are made by implementing technology with research, education and a manufacturing process that provides the craftsmanship needed for successful design.
Custom Fit is a Better Option
Many people try to treat flat feet with arch supports that they purchase over the counter. They may help somewhat or not at all. The best solution is orthotics for flat feet that are designed for your individual needs. The materials used will last for several years while providing the support your feet need and proper alignment of the legs when standing. In addition, flat feet are often associated with problems in the hips, knees and back. Support on a full time basis is needed and will be very beneficial to relieve many of these symptoms and to prevent further problems.
Foot orthotcs for flat feet should be made from a material that is lightweight for the best comfort. In addition, they offer shock absorption, which is very important. When standing, walking or running, weight is transferred to your feet. When they come into contact with the ground, this can cause an impact that for people with flat feet allows their feet to roll over to the inner side. This can put a strain on the ligaments and muscles in the legs. Arches in the feet help to distribute body weight in the legs and feet when walking on the many surfaces we come into contact with daily.
Orthotics are Beneficial for Many
Foot orthotics for flat feet can help by providing this distribution of weight for those who do not have arches. They are often recommended by health care providers for people who are experiencing pain from fallen or weak arches or hereditary flat feet. Diabetes is also a cause of flat feet and it is very important that the feet be protected when this condition is present. Arthritis sufferers can also benefit from orthotics as well as people with nervous system or muscle diseases.
For more information about getting Custom Foot Orthotics for your Flat Feet
Call 855-790-1687 or visit bit.ly/16RNG8a
via WordPress bit.ly/140Hrko
via Blogger bit.ly/1cipY6V
We, Ashwin Plastics, initiated our momentous lifework as producers and suppliers of plastic packaging products such as Laminated Pouches, Laminated Rolls, BOPP bags, BOPP rolls, HM bags and Rolls, PP Bags and Rolls etc. Offer diverse range of packaging products to meet varied requirements. Follow high quality parameters in business operation, manufacturing process and client servicing. Very particular about not using plastics and laminates that are safe and non-hazardous
From the planting of the seed to the end of the manufacturing process, Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
040
Friday, December 8th, 2017
Fortune Global Forum 2017
Guangzhou, China
8:00 AM–9:20 AM
SMART MANUFACTURING AND THE INTERNET OF THINGS
Around the world, factory floors and assembly lines are becoming highly automated, combining human ingenuity with data and technology to revolutionize product and productivity outcomes. As the notion of a “factory of the future” continues to evolve, how are companies incorporating “smart” and connected products into their manufacturing process? From sensors and robots to 3D printing and green technology, global companies are experimenting with a variety of methods to streamline, scale, and sustain their business. Here in China, manufacturers have been asked to deliver on the nation’s “Made in China 2025” strategy and are aggressively pursuing their own strategies to become smarter, greener, and more efficient. As these changes take hold, what are the implications for those doing business in China and for supply chains worldwide? And how are companies redeploying and reeducating their workforces as traditional factory jobs become automated and the need for technically proficient talent increases?
Hosted by The City of Guangzhou
Börje Ekholm, President and CEO, Ericsson Group
Till Reuter, Chief Executive Officer, KUKA
Tony Tan, Partner, Shanghai Office, McKinsey & Company
Wang Wenyin, Chairman, Amer International Group
Shoei Yamana, President and CEO, Konica Minolta
Zhang Jing, Founder and Chairman, Cedar Holdings Group
Moderator: Adam Lashinsky, Fortune
Photograph by Vivek Prakash/Fortune
Fresno State Industrial Technology Industrial Manufacturing Processes Class - Professor Don Austin, Jordan College of Agricultural Sciences and Technology, photo by Geoff Thurner, March 29, 2016, Copyright 2016.
Ten recently laid-off workers completed a unique program that teaches them new skills to help them land high-demand jobs in manufacturing. The Connecticut Business & Industry Association (CBIA), the Manufacturing Alliance Service Corp. (MASC), Waterbury Adult Education, and the Northwest Workforce Investment Board (NW-WIB) sponsored the program for dislocated workers. The 13-week program focused on shop essentials, math, and blueprint reading, along with hands-on CNC precision machine skills training, and lean manufacturing processes.
In Photo Front row: Luis Serrano, Waterbury
Back Row: (left to right) Edward Fitz, Woodbury; Jason Mancino, Torrington; Charles Jenner, Wolcott; Jeffrey Petriccione, Ansonia; Paul MacDonald, Wolcott; Paul Pelkey, Waterbury; Arnaldo Dulac, Winsted. Missing from photo: Tableegh Abdan-Nasir, Waterbury; Ernest Leno, Torrington; and instructor Robert Yenkner.
Click To Get Special Price Sleep Innovations 12-inch Sure Temp Memory Foam Mattress - King Size <<<< If you guys are looking for buying Sleep Innovations 12-inch Sure Temp Memory Foam Mattress - King Size at discount price, We have found a great deal and low price for this product on Amazon. Get it today!. Let's see the product description. The Sleep Innovations 12-inch SureTemp mattress provides premium memory foam comfort and superior therapeutic benefits at a great value. Rest in comfort with this best in class, deep and responsive 12-inch memory foam mattress. 2.5-inch top layer of Sure Temp memory foam shapes and molds to fit comfortably between the contours of your body providing all the benefits of traditional memory foam with the added benefit of a comfortable sleeping temperature. This unique, patented formulation and manufacturing process offers improved airflow for a cooler night's sleep. 9.5-inch base layer of high quality foam provides a supportive sleep surface that disperses your weight evenly, completely relieving pressure points. Mattress measures 80-inch long by 76-inch wide by 12-inch high. Mattress measures 75-inch long by 54-inch wide by 8-inch high.. Wanna buy this Sleep Innovations 12-inch Sure Temp Memory Foam Mattress - King Size? Special Offer, Click Here! www.amazon.com/gp/product/B003CT37LA/ref=as_li_ss_...
From the planting of the seed to the end of the manufacturing process,Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
From the planting of the seed to the end of the manufacturing process, Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
(En) Founded in 1906, the Coking Plant of Anderlues was specialized in the production of coke for industrial use.
Coke was obtained by distillation of coal in furnaces and, thanks to its superior fuel coal properties, it was used afterwards to feed the blast furnaces in the steel manufacturing process.
Closed and abandoned since 2002, the site has since undergone many losses and damages, not including an important pollution. While some buildings have now been demolished, there are however still some important parts of the former coking plant.
Among them, the former coal tower, next to the imposing "battery" of 38 furnaces, where the coke was produced. Besides them, we still can see the administrative buildings, the power station with its cooling tower, and buildings for the by-products, which were obtained by recovering the tar and coal gas. There are also a gasometer north side, the coal tip east side and a settling basin south side.
-----------
(Fr) Fondées en 1906, les Cokeries d'Anderlues étaient spécialisées dans la fabrication de coke à usage industriel.
Le coke était obtenu par distillation de la houille dans des fours et, grâce à ses propriétés combustibles supérieures au charbon, il servait par après à alimenter les hauts-fourneaux dans le processus de fabrication de l'acier.
Fermé et laissé à l'abandon depuis 2002, le site a depuis lors subi de nombreuses pertes et dégradations, sans compter la pollution qui y règne. Si certains bâtiments (comme l'ancien lavoir à charbon) ont aujourd'hui été démolis, on retrouve encore toutefois certaines parties importantes de cette ancienne cokerie.
Parmi celles-ci, l'ancienne tour à charbon suivie de près par l'imposante "batterie" de 38 fours, où était produit le coke. A côté d'eux, on découvre également les bâtiments administratifs, la centrale électrique avec sa tour de refroidissement, ainsi que les bâtiments des sous-produits, lesquels étaient obtenus par récupération du goudron et du gaz de houille. Et en périphérie, on retrouve un gazomètre côté nord, le terril à l'est et un bassin de décantation côté sud.
A Manufacturing Process photo contest online with Lenzr with a chance to win monetary prize for your picture license to be used on the process manufacturing and lean manufacturing company website.
Utthunga provides industrial data analytics services in predictive, prescriptive, descriptive and diagnostic analytics using the data coming from plant floor assets and manufacturing processes. Find out more on what we do!
utthunga.com/product-engineering/digital-engineering/anal...
(En) Founded in 1906, the Coking Plant of Anderlues was specialized in the production of coke for industrial use.
Coke was obtained by distillation of coal in furnaces and, thanks to its superior fuel coal properties, it was used afterwards to feed the blast furnaces in the steel manufacturing process.
Closed and abandoned since 2002, the site has since undergone many losses and damages, not including an important pollution. While some buildings have now been demolished, there are however still some important parts of the former coking plant.
Among them, the former coal tower, next to the imposing "battery" of 38 furnaces, where the coke was produced. Besides them, we still can see the administrative buildings, the power station with its cooling tower, and buildings for the by-products, which were obtained by recovering the tar and coal gas. There are also a gasometer north side, the coal tip east side and a settling basin south side.
-----------
(Fr) Fondées en 1906, les Cokeries d'Anderlues étaient spécialisées dans la fabrication de coke à usage industriel.
Le coke était obtenu par distillation de la houille dans des fours et, grâce à ses propriétés combustibles supérieures au charbon, il servait par après à alimenter les hauts-fourneaux dans le processus de fabrication de l'acier.
Fermé et laissé à l'abandon depuis 2002, le site a depuis lors subi de nombreuses pertes et dégradations, sans compter la pollution qui y règne. Si certains bâtiments (comme l'ancien lavoir à charbon) ont aujourd'hui été démolis, on retrouve encore toutefois certaines parties importantes de cette ancienne cokerie.
Parmi celles-ci, l'ancienne tour à charbon suivie de près par l'imposante "batterie" de 38 fours, où était produit le coke. A côté d'eux, on découvre également les bâtiments administratifs, la centrale électrique avec sa tour de refroidissement, ainsi que les bâtiments des sous-produits, lesquels étaient obtenus par récupération du goudron et du gaz de houille. Et en périphérie, on retrouve un gazomètre côté nord, le terril à l'est et un bassin de décantation côté sud.
Red Hue clothing is a contemporary clothing line, diverse in style and fit. Inspired by real women, Red Hue clothing offers quality and fashion in one. Modern with a retro feel, Red Hue strives to be timeless and ageless. We are proud to say our brand is 100% sweatshop free! The clothing is manufactured in an atelier styled workshop in El Salvador,designer Silvia Huezo’s home country, where hardworking hands hand cut and assemble the garments. Our manufacturing process is closely monitored to ensure the just treatment of those who work so hard on the pretty clothes we wear.
The design process started with a cost prohibitive idea of creating a fully functional multi-piece plastic astrolabe that would cradle the CD as well as do everything an astrolabe does. When i started pricing the supplies and manufacturing process involved it became clear that 1. this was going to be a stunning piece of work if completed, & 2. it was going to be VERY expensive.
Ipecac did not spring for the $6 per unit cost that would have been incurred to make the astrolabe design. It’s a shame really as this would have been a truly stunning unique piece of packaging.
regardless it still looks quite nice and has potential for future applications somewhere somehow.
Ascent Heat Exchanger Copper Nickel Tube ♣ Top China Heat Exchanger Copper Nickel Tube Supplier
❤About Ascent Heat Exchanger Copper Nickel Tube：
We manufacture, process and sell heat exchanger copper nickel tubes of good quality and dependability you can rely on. Shop for other equally qualified tubes of heat exchanger copper alloy tube, coopper nickel tube, etc. at our website of ascentcopper.com. Save time and shop with the trusted brass tube manufacturer.
❤Description:
Applied vacuum melting technology, our tubes are of superior quality: stable chemical composition, precise dimensions, and clean, smooth and bright inner and outer surface. Good mechanical properties - free from defects such as blowholes, cracks, pin hole leaks etc.
❤Features:
* Good corrosion resistance, especially in sea water; * Suitable for high temperature service; * Applicable for condenser for ship, heat and water supply, chemical industry, desalinator etc.* Copper Alloy UNS Nos.C70600 and C71500 are seamless Copper Nickel Tubes of standard specifications for Water Desalting Plants.
OD Range:3mm to 70mm
Wall Range:0.2mm to 5mm
Shape:Seamless Tube
Juices Hayler - is a premium quality product. The juices have exquisite taste and aroma of natural fruits and are abundant in vitamins and minerals. The manufacturing process of juices is implemented by means of modern equipment. The established quality is according international standards.
What are the differences between Plastic Manufacturing Processes? Please visit the website www.pangeatech.us/, There are different methods of manufacturing plastic. The most common methods are the following – Injection molding, Blow molding, Vacuum casting, Plastic extrusion, Rotational molding, Thermoforming and Compression molding. For better results, watch the Video.
Lowest Price :Visit store to see price You Save : On store
Best Cheap Deals 100 SONY CD-R Music Disc, Digital Audio Recordable For CD Recorders and Computer Writer, 5 Assorted Color, 80 minStrict quality control andsuperior manufacturing processes, enable Sony CD-R to deliver the mechanic...
In this work mussels are lashed into an electro-stimulated design apparatus to make a vase. They are allowed to relax up to a certain point, then shocked, prompting movement that scratches a design onto the object. The resulting form might be seen as a sobering memento mori, a reflection on manufacturing processes that exploit biology.
credit: Florian Voggeneder
We, Ashwin Plastics, initiated our momentous lifework as producers and suppliers of plastic packaging products such as Laminated Pouches, Laminated Rolls, BOPP bags, BOPP rolls, HM bags and Rolls, PP Bags and Rolls etc. Offer diverse range of packaging products to meet varied requirements. Follow high quality parameters in business operation, manufacturing process and client servicing. Very particular about not using plastics and laminates that are safe and non-hazardous
A Medical Device Master File is a submission to U.S. FDA that may be used in support of premarket submissions to provide confidential detailed information about establishments, processes, or articles used in the manufacturing, processing, packaging, and storing of one or more medical devices. Registrar Corp's team of medical device regulatory experts provides guidance as to required elements, formats, and particularities of Medical Device Master File submissions. For assistance submitting a Medical Device Master File, simply click the Medical Device Master File Certificate shown on the left.
The Kart Factory Tour at the University LIUC Cattaneo in Varese, Italy provided ITA Students and Faculty the opportunity to interact with Italian innovation in manufacturing processes.
GC Pharma Probiotics for Kids (90 Count, Pack of 3) - Stomach-Friendly Yogurt Flavor Powder. 1.8 Billion CFU, Vitamin D 1,000 IU, Zinc 8.5mg
Get 15% Off With the (15QSSM1V) Christmas sale on all GC Pharma Products at www.amazon.com/dp/B09P4PQDGY?ref=myi_title_dp&th=1
About this item
1.8 BILLION ORGANISMS PER SERVING - 3 Month Supply (90 packets, 3 boxes) of yogurt flavor powder. Probiotic Kids is the ultimate bone growth supplement delivered together with living probiotic organisms. Friendly, non-invasive for your stomach.
VITAMIN D 1,000 IU, ZINC 8.5MG - In addition to immune support, getting a sufficient amount of Vitamin D is critical to building and maintaining strong bones in adults. It is essential for calcium absorption to help support healthy bones.
17 STRAINS & PREBIOTICS & POSTBIOTICS - Formulated with 17 probiotics strains per serving, sufficient prebiotic fiber blend for probiotics to colon and postbiotics for direct benefits. Our probiotics give you powerful support for balanced intestinal ecology and immune system. Great for gut health, gas relief, bloating relief, constipation, diarrhea, abdominal discomfort, digestive health.
EASILY TAKE ONE A DAY - Take it without water or pour the powder into your mouth directly and dissolve it with the naturally secreted saliva. Enjoy mild peach flavor. Our probiotics are shelf-stable, individually sealed and no refrigeration required. Powder form is meant to absorb better than capsules.
BRAND TO TRUST - Est. 1967, GC Pharma is one of the leading brands in South Korea for dietary supplements. Every GC Pharma’s product is subjected to numerous quality tests throughout the manufacturing process to verify purity and potency. Proudly manufactured following current good manufacturing practices (cGMPs) and Third-Party certified.
A brace of AMD Opteron 248 processors.
Core Sledgehammer stepping 0xC0
Socket 940
Package: lidded ceramic micro-PGA
Manufacturing process 0.13 micron SOI
Clock 2200Mhz
Taken using a Canon Rebel XT
Canon 50mm f1.8 EF lens
focal length: 50mm
ISO 100
Aperture: f/7.1
Shutter: 1/80
From the planting of the seed to the end of the manufacturing process, Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
Minton Tiles
The richly patterned and colored Minton tile floors are one of the most striking features of the extensions of the United States Capitol. They were first installed in 1856, when Thomas U. Walter was engaged in the design and construction of vast additions to the Capitol (1851-1865). For the floors in his extensions, Walter chose encaustic tile for its beauty, durability and sophistication.
•Artist: Minton, Hollins and Company
•Date: Installed in 1856
One striking example of the contrast between the interiors of the Old Capitol (finished in 1826) and the extensions (begun in 1851) may be seen in the differences in flooring materials. In the Old Capitol, stone pavers were used in corridors and other public spaces, such as the Rotunda and Crypt, while brick was used to floor committee rooms and offices. These materials, although durable and fireproof, would have looked plain and old-fashioned to the Victorian eye. In the mid-19th century, encaustic tile flooring was considered the most suitable and beautiful material for high-traffic areas. Unlike ordinary glazed tile, the pattern in encaustic tile is made of colored clays inlaid or imbedded in the clay ground. Because the color is part of the fabric of the encaustic tile, it will retain its beauty after years of wear. One observer noted:
“The indestructibility of tiles may be judged from the fact that the excavations at Pompeii have unearthed apartments where painted tiles are just as beautiful, the colors as fresh and bright as... when the fated city was in all its glory.”
Two types of tile were used at the U.S. Capitol: plain and inlaid encaustic tiles in a range of colors. Plain tiles were used as borders for the elaborate inlaid designs or to pave large corridor areas. They were available in seven colors: buff, red, black, drab, chocolate, light blue and white. Additional colors, such as cobalt blue, blue-gray, and light and dark green, appear in the inlaid encaustic tiles that form the elaborate centerpieces and architectural borders. They were made by “filling indentations in the unburnt tile with the desired colors and burning the whole together.”
The patterns and designs formed in the inlaid tiles were limited only by taste and imagination. They include geometric patterns such as the Greek key, guilloche, and basket weave; floral designs such as the fleur-de-lis; and figures such as dolphins and classical heads. Few of the patterns are repeated. Although most of the tiles are six-by-six-inch squares, some are round, triangular or pie-shaped. Approximately 1,000 different tile patterns are used in the corridors of the Capitol alone, and up to 100 different tiles may be needed to create a single design.
The original encaustic tiles in the Capitol extensions were manufactured at Stoke-upon-Trent in Staffordshire, England, by Minton, Hollins and Company. The firm’s patented tiles had won numerous gold medals at international exhibitions and were considered the best tiles made. In 1876, having seen Minton’s large display at the Centennial Exhibition in Philadelphia, one critic wrote, “Messr. Minton shone superior to all exhibits of the sort… and may be cited as showing the highest results in tile-pottery achieved by modern skill and research.”
Beginning in 1856, and continuing for five years, the tile was installed by the import firm of Miller and Coates of New York City. For the journey from New York to Washington, the tiles were packed in wooden casks weighing about 1100 pounds; each cask contained enough tiles to pave about 100 square feet. The cost of the tile ranged from $0.68 to $2.03 per square foot.
Thomas U. Walter had every reason to believe that the encaustic tile floors would last as long as his extensions stood. One visitor noted in 1859 that the tile floors vied with the beauty of marble and surpassed it in durability. While perhaps valid for other installations, however, this prediction proved overly optimistic for the Capitol Building. By 1924, the Minton tile was removed from the corridors in the first and second floors of the House Wing and replaced by “marble tile in patterns of a simple order.” In that day, marble was selected for its superior durability and because suitable replacement tile was difficult to find.
In the 1970s, however, a similar condition prompted a very different response. In 1972, a search was undertaken to determine a source of similar tiles in order to restore the original appearance of the building. Inquiries were made of all major American tile manufacturers, the American Ceramic Tile Manufacturers Association, and even Mexican and Spanish tile suppliers. Although the colors and designs could be reproduced relatively easily, the patterns would quickly wear because they would be applied to the surface. The “inlaid” feature of the encaustic tiles, i.e., the approximately 1/8-inch thickness of the pattern and color, is the characteristic that enables the Minton tiles to be walked upon for over 100 years without signs of wear. It was this technique that formed the basic difficulty of manufacture.
Finally, as a result of the Capitol’s needs becoming generally known, the Architect of the Capitol was placed in contact with H & R Johnson Tiles Ltd., located at Stoke-on-Trent, England. It was discovered that that firm was a successor company to the Minton Tile Co. and had even retained many of the original hand tools and forms in a private museum at the company’s manufacturing site.
Contact was then made with Mr. James Ellis, the Directing Architect of Ancient Monuments and Historic Buildings for the Crown. He had been trying for many years to establish a program for the replacement of the worn Minton tiles at the Houses of Parliament but had more or less given up the attempt because of H & R Johnson’s continued unwillingness to revive the encaustic tile process. However, the restoration work at the Arts and Industries Building of the Smithsonian Institution was in process at about the time the needs of the Capitol became known; it thus appeared that a market for such tiles was developing to the degree that the manufacturer began to reconsider its prior position. The company thus began the experiments that finally led to the present availability, after many decades, of the original Minton-type tiles.
Because the tiles in the Capitol are more decorative and have more complicated designs and color combinations than those in either the Houses of Parliament or the Smithsonian, those institutions were able to obtain replacement tiles sooner than the Capitol. The lessons learned in the manufacture of the simpler tiles served as a basis for filling the later needs.
Color photographs and full-sized drawings of the many required patterns were made and recorded, and many developmental submissions were made as the hand-made manufacturing process was re-developed. Finally, in 1986, the first acceptable tiles were delivered. The installation process was accomplished with modern cement adhesives and has yielded excellent results.
The program enabled the original tiles to be replaced with exact replicas. This project began on the first floor of the Senate wing, where the effects of 130 years of wear and tear were most noticeable. Replacement tile was closely scrutinized to ensure fidelity to the nineteenth-century originals. While difficult and slow, this process is the only fitting response to the history of the Capitol extensions, not only to restore the original beauty and elegance of these unique floors, but also to provide for their continuing attractiveness for the foreseeable future.
Location: Lichfield District Council
Accession number: GL07
A wine glass with round funnel bowl and double knop stem, manufactured in England in the late 18th century.
The glass has a plain, undecorated round funnel shaped bowl. The stem of the glass is decorated by twisting threads known as a multi-spiral air twist. Two rounded bumps known as knops are also located on the stem of the glass.
The glass sits on a conical foot with an unground pontil. This pontil is a bump which was left over from the manufacturing process and marks the point where the glassblower's pipe was attached to the glass.
The air twist style of stem manufacture occurred within the British glass making industry between 1730-1780. The effect was achieved by piercing the base of the glass bowl with a circle of nails whilst the glass was still molten. This introduced air bubbles into the base of the bowl. The stem was then pulled or 'drawn' and simultaneously twisted to form the spiral effect.
QR code
From Wikipedia, the free encyclopedia
A QR code (abbreviated from Quick Response code) is a type of matrix barcode (or two-dimensional code) first designed for the automotive industry. More recently, the system has become popular outside of the industry due to its fast readability and comparatively large storage capacity. The code consists of black modules arranged in a square pattern on a white background. The information encoded can be made up of any kind of data (e.g., binary, alphanumeric, or Kanji symbols).
Created by Toyota subsidiary Denso Wave in 1994 to track vehicles during the manufacturing process, the QR code is one of the most popular types of two-dimensional barcodes. It was designed to allow its contents to be decoded at high speed. The technology has seen frequent use in Japan; the United Kingdom is the seventh-largest national consumer of QR codes.
This Video Is About The Ferrite Metal Solutions Pvt. Ltd Welding Manufacturing Process. Ferrite is A Company Dedicated To The Philosophy Of Providing Quality Products To The Industry. Founded in Year 2000, Our Success As A Young Company Is Based On Our Market-Focused, Customer-Centric Approach, Which Improves Our Products, Increases Our Efficiency And Makes It Easy For Customers And Suppliers To Do Business With Us The World Over.
Custom Presentation Folder / Pocket Folder with Brochure Insert
Type of Paper: 80# Diamond Gloss Cover - FSC
Printing Process: Offset Printing
Number of Colors: 7/7 Overall Satin Aqueous Coating
Binding: Trim, Score, Fold and Pack
Page Size: 25.5" x 11"
Finished Size: 8.5" x 11"
This presentation folder and brochure had very tricky cross page line ups. We spent the time to make sure all line ups we accounted for in all manufacturing processes.
From the balcony of Eleutherian Mills, the du Pont family home at the gunpowder factory at Hagley, you can see the sunken remains of a garden. The garden contains artifacts from manufacturing processes that were old when the garden was built. Because it was built over an area of tunnels that have since collapsed, no one can go into the gardens anymore.
Next to the creek are ruins from the original gunpowder mills from 1802.
Visit the Hagley Museum & Library near Wilmington, Delaware.
I did a lot of brazing for training purposes before building my firs own fork.
Joints were cut to analyse solder distribution and connection between materials.
Enjoyed the improvement in the manufacturing process!
On Scene with Watertown Volunteer with a smoky structure fire at 20 McLennan Dr in the Oakville section of town. First due crews found heavy smoke coming from Quality Automatics Inc ,a machine shop located at that address. Crews immediately stretched lines and hit the hydrant at the end of the dead end street for an additional water source. Extension ladders were used to access the roof for ventilation since powerlines prevented the aerial ladders from being used. The fire was brought under control after approximately 30 minutes but required extensive overhaul and ventilation. In addition hazmat precautions had to be taken due to the lubricants and by products of the manufacturing process at the business were mixed with the water and foam used to extinguish the blaze.
From the planting of the seed to the end of the manufacturing process,Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
040
Friday, December 8th, 2017
Fortune Global Forum 2017
Guangzhou, China
8:00 AM–9:20 AM
SMART MANUFACTURING AND THE INTERNET OF THINGS
Around the world, factory floors and assembly lines are becoming highly automated, combining human ingenuity with data and technology to revolutionize product and productivity outcomes. As the notion of a “factory of the future” continues to evolve, how are companies incorporating “smart” and connected products into their manufacturing process? From sensors and robots to 3D printing and green technology, global companies are experimenting with a variety of methods to streamline, scale, and sustain their business. Here in China, manufacturers have been asked to deliver on the nation’s “Made in China 2025” strategy and are aggressively pursuing their own strategies to become smarter, greener, and more efficient. As these changes take hold, what are the implications for those doing business in China and for supply chains worldwide? And how are companies redeploying and reeducating their workforces as traditional factory jobs become automated and the need for technically proficient talent increases?
Hosted by The City of Guangzhou
Börje Ekholm, President and CEO, Ericsson Group
Till Reuter, Chief Executive Officer, KUKA
Tony Tan, Partner, Shanghai Office, McKinsey & Company
Wang Wenyin, Chairman, Amer International Group
Shoei Yamana, President and CEO, Konica Minolta
Zhang Jing, Founder and Chairman, Cedar Holdings Group
Moderator: Adam Lashinsky, Fortune
Photograph by Vivek Prakash/Fortune
John Allison is William F. Hosford Professor of Materials Science and Engineering at the University of Michigan and a National Academy of Engineering member.
His major research interest is in understanding the inter-relationships between processing, alloying, microstructure and properties in metallic materials – and in incorporating this knowledge into computational tools for use in research, education and engineering. An important part of his research is development of Integrated Computational Materials Engineering (ICME) tools – and thus collaborations with other computational and experimental groups are an essential element of my work. Central to my research are investigations on the evolution of microstructures - current examples include precipitate evolution, recrystallization and grain growth and texture development in magnesium, aluminum and titanium alloys. He is also interested in mechanical behavior of these materials, with an emphasis on development of mechanistic and phenomenological understanding of the influence of microstructure on properties such as strength, ductility and fatigue resistance.
Allison comes to the University from Ford Motor Company, where he was a senior technical leader in the Research and Advanced Engineering organization. Over the twenty seven years of his tenure at Ford, he led teams developing integrated computational materials engineering, or ICME, methods. He helped develop advanced computer software that simulates manufacturing processes and predicts the influence of the manufacturing process on material properties. The output of these models is then coupled with product performance models to predict how manufactured components will behave during service.
July 11, 2023.
Photo by Marcin Szczepanski/Lead Multimedia Storyteller, Michigan Engineering
www.lcrapid.com/cnc-machining/
At LC Rapid, ou precise, quick-turn, custom CNC machining services China makes parts from a wide variety of certified metal and plastic materials. Our CNC service including CNC milling, CNC turning, wire EDM, and much more.
With advanced CNC machining centers and experienced employees, we offer the same high-quality parts and satisfactory services to large and small companies alike, from Fortune 500s to innovative start-ups.
Introduction of CNC Machining Services
CNC (Computer Numerical Controlled) is an automated manufacturing process to remove materials from a simple plastic or metal block with a serial of cutting tools to make the custom CNC machined parts. Advanced software is used to control the high precision machining according to the required specification of the CAD (Computer Aided Design) model provided by the customer. The support from LC team of engineers will program the CNC machining center to create the final products with a high level of part complexity, and provide exceptional surface finishes. As a professional CNC machining solutions inc, we are continuously offering a cost-effective CNC custom machining whether you need prototypes, production orders or mold tools that are used for plastic injection molding or pressure die casting services.
Advantages of Precision CNC Machining
Fast Turnaround
Using the highly advanced CNC machines, LC Rapid can manufacture precise parts in 1 day.
Precision
High dimensional tolerances and precision can be assured by applying CNC machining.
Different Finishing Options
CNC machining offers great surface finishing, we also offer a full range of finishes on metal and plastic parts, from sand blasting, anodizing to plating, brushing, polishing to painting.
High Scalability
CNC Machining is suitable from one single part to production runs 100,000 parts thanks to robust, round-the-clock machines.
Material Selection
There are a wide range of certified rapid prototyping and production materials can be selected, from commonly used aluminum, stainless steel and plastics to more exotic materials like titanium, carbon fiber .
Cost Effectiveness
Low investment in tooling and quick removal of raw materials guarantee CNC machining a cost effective way for both prototyping and high production volumes.
CNC Machining Process
Multi-Axis CNC Milling Centers
3-axis CNC machining center
4-axis CNC machining center
5-axis CNC machining center
CNC Machining Tolerances
With high precision and stable quality, we are able to ensure a great dimension accuracy for prototypes and production parts. CNC engineering is an automated process which can eliminate human errors and assure the consistency of batch quantity. We will make parts base on client's specification. If you don't specify your tolerance requirement, our general tolerances standard is DIN-2768-1-fine for metals and DIN-2768-1-medium for plastics.
CNC Machining Materials
CNC precision machining involves a variety of engineering-grade plastic and metal materials including ABS, Nylon, PMMA, and Peek to aluminum, steel, magnesium and brass. We can make parts for CNC prototyping parts and low-volume production without being limited by material types. Please do contact us if you need a specific material that does not show in the list, we are glad to source the customized raw material upon your request.
From the planting of the seed to the end of the manufacturing process,Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
From the planting of the seed to the end of the manufacturing process, Portuguese cork makes for authentic, high quality and eco-efficient cork products that are created with true craftsmanship and care.
Polyphon is a disc-playing music box, a mechanical device first manufactured by the Polyphon Musikwerke, located in Leipzig, Germany. Invented in 1870, full-scale production started around 1897 and continued into the early 1900s. Polyphons were exported all over world and music was supplied for the English, French and German markets, as well as further afield, with music cataloged for the Russian, Polish and Balkan regions. Polyphon is also a record label as registered by German Polyphon Musikwerke AG in 1908. Polyphon handled as Polydor label since 1913 with their trademarks Polyphon Musik and Polyphon Record.
Making music
The tune is punched out on the disc with pitch determined by the position of the punching. In the manufacturing process, the punched metal was curled back onto the underside of the disc, creating a raised projection that resembles a letter P when viewed obliquely. When the Polyphon operates, the resulting disc projections, called plectra, engage with a series of ratchet-like star wheels, each with 9 projections, that sit in a gantry. Each star wheel, when moved through 40 degrees on its axis, plucks a tooth on the instruments comb. The tooth then resonates, sounding a predetermined note.
Upon the musical comb, the fast treble notes are sounded furthest from the centre and the slower base notes nearest the centre. Many comb variants were manufactured, including a single comb on smaller instruments, and duplex combs (simultaneous strike) on mid-sized examples of 11-inch-diameter and 15.5-inch-diameter instruments. Most larger twin-combed examples had alternate strike although other manufacturers, notably Symphonion, produced large size instruments with duplex combs.
Motor
Almost without exception, all Polyphons are powered by a hand-wound clockwork motor. Polyphon may have devised an electric motor variant of a large coin-operated model in the latter days of production, but to date, no known original examples exist.[citation needed] The motor has an output drive dog, which is a circular component with round-topped dowels arrange to fit the holes in the discs. Discs of small diameter have two centrally located holes (centre drive), while larger discs had a series of holes around the periphery (peripheral drive).
During operation, a disc is placed on the centre post, or centre boss, a pressure bar goes over the disc to hold it in place and the drive dog revolves the disc. The playing time for each disc varies, dependent upon the diameter; for example, the running time of an 8-inch-diameter disc is about 1 minute and 50 seconds.
Source: Wikipedia
In Buriram NKT Carbon Brushes save your electronics and save your money by giving them maximum power, extra durability,
and also give your Power Tools longer lifetime.
With this quality of NKT Carbon Brushes, you will work much more safely, precisely and more productively.
Over 30 years experiences, NKT has long been recognized among the highest quality carbon brushes in the industry.
Our objective is to satisfy your increasing demand by our impressive quality and service.
To achieve our goal, NKT uses the most elaborative manufacturing processes and quality control
to assure every tool meets professional standards.
Only the highest quality raw materials are selected in manufacturing processes guaranteed by Germany hi-class technology. Dial 044-666-484 and press "O" for assistance in English. Bring any tool that needs a quality NKT carbon Brush for immediate replacement by the service staff of Ruangsangthai.