View allAll Photos Tagged compressor
1. It's cooled by water, air or mixed cooling.
2. Automatic control and protection system.
3. Capacity: 0.5~3m3/min.
4. Pressure: 2.5~40Mpa.
CRS D 20 Series Rotary Screw Compressors,Quiet noise levels, as low as 68 dB(A).Microprocessor manages Control Functions (start, stop, reset), Operating Conditions (load, idle, stop), Safety Alarms (oil temperature, motor trip switch, solenoid trip switch, air press, maintenance time)
CRS 10/500 Series Rotary Screw Compressors,Microprocessor manages Control Functions (start, stop, reset), Operating Conditions (load, idle, stop), Safety Alarms (oil temperature, motor trip switch, solenoid trip switch, air press, maintenance time)
Ardnamurchan lighthouse. The compressor house has been left undisturbed since the fog-horn became defunct.
CRS 25 Series Rotary Screw Compressors, Quiet noise levels, as low as 68 dB(A).Easy access to all serviceable parts means shorter downtimes and reduced cost for the user during scheduled services
CRS 20/500 Series Rotary Screw Compressors,Intelligent software controls energy consumption, and automatically regulates the idle run time, reducing the number of stop/start cycles during 2 daily work cycles, and 3 yearly periods of in-activity
The audio compressor or a unity-gain amplifier having an expansion of 3 db and a compression of 12 db around an average level of approximately 45 db below 1 volt at an impedance of 100.000 ohms. The compressor is inserted after the microphone amplifier. The incoming audio signal is amplified by U1a and applied to the diode compressor through C1. The diode compressor is essentially an L-pad attenuator, with R1 forming one leg and diode D3 for the other leg. Diode D1 rectifieds the audio signal and applies the resultant DC voltage through R2 to diode D3. The impedance of D3 varies almost logarithmically in inverse porportion to the DC voltage across it. Diode D2 protects filter capacitor C2 from any reverse polarity switching transients that may be applied from the output. The curves of Fig-2 show that about 15 deb attenuation is availaBLE. A portion of this loss is made up in the opamp, thus permitting installation of the unit as a unity-gain amplifier with an expansion of 3 db and compression of 12 db. Total conasumption is approximately 4mA. The frequency response of the compressor for various input levels is shown in Fig. 3. A tape recorder using this automatic gain compressor has been successfully used to report events from the quiet of an empty hall to the noisycockit of a small private plane.
The audio compressor or a unity-gain amplifier having an expansion of 3 db and a compression of 12 db around an average level of approximately 45 db below 1 volt at an impedance of 100.000 ohms. The compressor is inserted after the microphone amplifier. The incoming audio signal is amplified by U1a and applied to the diode compressor through C1. The diode compressor is essentially an L-pad attenuator, with R1 forming one leg and diode D3 for the other leg. Diode D1 rectifies the audio signal and applies the resultant DC voltage through R2 to diode D3. The impedance of D3 varies almost logarithmically in inverse proportion to the DC voltage across it. Diode D2 protects filter capacitor C2 from any reverse polarity switching transients that may be applied from the output. The curves of Fig-2 show that about 15 db attenuation is available. A portion of this loss is made up in the opamp, thus permitting installation of the unit as a unity-gain amplifier with an expansion of 3 db and compression of 12 db. Total consumption is approximately 4mA. The frequency response of the compressor for various input levels is shown in Fig. 3. A tape recorder using this automatic gain compressor has been successfully used to report events from the quiet of an empty hall to the noisy cockpit of a small private plane.
CRS D 10/500 Series Rotary Screw Compressors, Microprocessor manages Control Functions (start, stop, reset), Operating Conditions (load, idle, stop), Safety Alarms (oil temperature, motor trip switch, solenoid trip switch, air press, maintenance time)
Thicker planks to squeeze the veneer between, to try and keep it a uniform thickness.
Trying to keep a handle on the grain orientation of each piece.
Using Titebond 3 with the black veneer will be ok because the dark glue line will not be noticeable, hopefully.
Gardner Denver EBPOMB
Air Compressor
Year Of Make: 1993 & 1995
Capacity: 100 HP
Speed: 1800 RPM
Electrics: 575V/3PH/108A
-EQUIPPED WITH-
Receiver Tanks
Moisture Separators
Dryers
2" Piping
***TWO OF THESE MACHINES AVAILABLE***