View allAll Photos Tagged Howto
If you have a paper ticket, this is the most important thing to remember to pack. Wallets are good places to put precious things, as long as you don't get mugged. Or, you could try stapling your ticket to your forehead. The sooner you pack your ticket somewhere safe, the sooner you can stop worrying about it.
But: don't pack your ticket in a bin with your gear. You'll need your ticket at the gate to get into burning man, and you won't want to have to unpack and then repack your vehicle just to get through the gates.
Super easy and cute DIY makeup storage! , lomics.co/l/2jted7ylCE
Download Lomics:
IOS - m.onelink.me/de143c61
Android - m.onelink.me/5301f4f0
Enable your new feathers by selecting them from the Feathers menu. Since your feathers are copied from the default Rubberducky, you won't notice anything different until you change something.
No adjustments just a crop and re size in post.
www.flickr.com/photos/florida_sail_ham/sets/7215762490628...
Welcome to your new sandbox. These files are used to paint the appearance of your Songbird. They are basically a copy of Rubberducky for you to modify as much, or as little, as you'd like.
Please follow this link to read the article. blog.jaredpolin.com/home/2008/12/23/a-how-to-guide-to-cap...
No adjustments just a crop and re size in post.
www.flickr.com/photos/florida_sail_ham/sets/7215762490628...
- Put bread in toaster on light setting til it's just brown.
- Slather with butter [you can melt butter first on warm bread]
- add cinnamon and sugar
- put back in toaster til the whole mess bubbles
- enjoy, careful sugar is HOT [and delicious]
after clicking install you should see the message this item will be installed after you restart firefox
Now to read:
The mark that tells you what the actual measurement is the long line on the bottom left (I've marked it with a red arrow). Then look up to the center part of the gauge and find a corresponding number. Some gauges are more accurate than others (depends on how they were calibrated). This might make measurements between gauges differ by .1mm or more.
Here it looks like it is almost on the 16mm mark/line. Depending on how accurate or annoying I want to be I can call this eye 16mm (what it was sold as) or I can get into a finner measurement.
Since the measuring line between the 15 and 16mm (or 1.5cm and 1.6cm) marks I know that it will be under 16mm and over 15mm. I also know that the measurement should be more than 15.5mm since it's so close to the 16mm line. This type of estimation is usefull as it allows me to double check further numbers.
The other lines/marks that follow the red arrowed line, the measuring line, show me the decimal place. They are 0.1mm increments.
To find which one, I look for the 0.1mm line (on the red arrow side) that matches up perfectly (or as close as possible) to a line with the numbers (in the center piece of the gauge). DO NOT LOOK AT THOSE NUMBERS IN THE CENTER. You only need the lines.
The line that matches up closely are the two lines that I've underlined in blue. Personally I think the 8th one is the best, but this can be up to some debate (between 8 and 9). These lines on the red arrow side tell you the 0.1mm increment of measurement, so count the lines (there are ten, with the .5mm mark being the center line that is not as short as the others. Its longer but not as long as the red arrow line.) and that tells you what the measurement is to the tenth decimal place.
So the measurement of this eye is 15.8mm in diameter or 16mm as eyes are usually sold in increments of 2mm.
If you wanted to read the inch size (why???) just look at the one mark on that size and find the closest measurement mark. Here it would be approximately 5/8inches. Again this is not as accurate. Look at all the spaces between the marks on the inch side.
We all make mistakes, but SRAM mechanic Sara Jarrell says she frequently meets cyclists who make the same common errors when it comes to bike set up and maintenance. She has wrenched for World Cup racers, led skills clinics for riders of all abilities and taught beginner classes, so she’s ex...
Align your horizontal planks (the 5 1x6s), face down on your work surface. Place a support plank on top, set 1" down from the top of the headboard and about 5" from the sides of the headboard.
This can take many tries, as pushing a small needle through 3 inches of foam, batting, and fabric is not exact. Try not to put too many holes in your front fabric! Once you get the needle to push through into the drilled hole, you should pull it out, using the needle nose pliers if necessary.
If you've upload a video, you'll see it under "Videos"... if you've linked to a remote file, you'll see N/A for the preview.