View allAll Photos Tagged HowTo,
Squeeze and lengthen the strip until you can cut it into slices, with a single sided blade, thin enough to produce individual leaves. You can cut slightly thicker pieces for the centre.
Grap piece A and WRONG side up fold the RIGHT side over about ¼“, then fold again, about ¾”. This will be the "casing" where your buttons will go.
Finish the top edge, or measure where it will be so you have a better idea on where to put your buttons.
The trick is to click on the title of the article in the reading pane, THEN click on the bookmark-looking "read it later" button.
Pull out a needle and sew those buttons on!
You are going to sew your buttons inside the "casing." Now, when the bodice is inside out, you can't see the stitches, instead you see the clean right side of the fabric.
I glue each of the 0.188" styrene angle pieces to a corner with Crazy Glue. The glue sets quickly so I had to be sure to drop it in the corner carefully.
I used a pencil to hold it in place while it set. I only need to wait about 30 to 60 seconds.
I just started using black flux for stainless. It rocks. When it's up to temp, it turns clear and it lasts a long time.
The vice grips aren't clamped on there very hard - just enough to make sure the stainless isn't going anywhere while I tack it.
Soaking in a hot tub is one of the best ways to relax and let go of the tensions of your daily life. But when it’s time to move the hot tub, it can be one of biggest reasons to stress you out. Moving a hot tub is no child’s play because of the size, weight, and the irregular dimensions of the hot...
Illustration by Larry Largay
When you’re fishing a bend in a river, make sure that you fish the water close to you before you cast to the real “lunker water” against the far bank. Start from the tailout and work upstream, beginning at the tailout (A). Next, look for trout near any rocks or structure on the inside of the main current (B). Oftentimes, there will be fish lying right out in the open on the inside of the bend (C); these fish are usually quite wary, so you need to be stealthy and make delicate presentations. Finally, look for fish at the head of the pool (D) where there are rocks that break the current. Caption 2: Just because the guidebooks say that the trophy trout hold in the deep channel or beneath the undercut bank along the outside of a river bend, it’s not unheard of to see big fish finning in the shallows on the inside of the main current.
Have an opening graphic that people can see when they walk in the room and know they're in the right place. Also, if you're smarter than me you might even get the date right, though this was a great conversation starter as people walked in to the room "...wait, you're going to Australia??"
1. triple hazelnut mousse, 2. Sonja's cupcakes, 3. sansrival piece, 4. rose cupcake (2), 5. decadence choco cake, 6. carrot cake, 7. caramel cake, 8. choco cake (5), 9. Better Than Sex cake, 10. banana cream pie 3, 11. banana cake, 12. white velvet side, 13. fallen chocolate cupcakes, 14. Karen's s'berry cc, 15. turtle cake, 16. Dessert_Show_Pics_004
Created with fd's Flickr Toys.
Roll a centre and cut into the top to simulate individual leaves. Add single pieces to the outside. Two should be enough but you could use four or more.
How-To build an Ultralight SOTA Antenna for the ham radio activity Summits On The Air. See the full guide here: seeksolitude.com/?p=166
Fold your fabric in half, right sides together. Lay your chair on top of the fabric and using a pencil trace the outline of the chair. The outline needs to be at least 1" larger than the chair. If your chair is thicker, you're going to need more than 1". If it has a defined, wide side, you're going to have to cut a separate piece for that. If you make the slipcover too big, you can always cut some off, but there's no solution for too small!
If your chair tapers like mine does (the bottom being smaller than the top), make sure not to make the bottom too narrow, or you won't be able to fit it over the wider top.
I cut straight down with a hacksaw with the seatstay angled. This is all approximate - no measurement necessary.
The seatstay is a single taper 16mm - fairly thick walled.
