View allAll Photos Tagged oscillator

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

at Musikzimmer, Kunstraum Aarau, 19 February 2012. Finissage of ILIOS exhibition "Polaplasiepimoria". Car used: Peugeot 406 beak 2.0

www.siteilios.gr/ILIOSSym.html

Hacker Helmsman RP36 _ switch card with RF oscillators .

Sonic Acts festival

Paradiso, Amsterdam 2015

 

A very physical negotiation of territories voided by history, rendered via field recordings gathered over ten years in over 30 remote locations in Australia, alongside new work with pipe organ, guitar feedback, dubplates, turntables and low frequency oscillators.

Eight oscillators, polyphonic, touch sens keys on an Arduino - WOW!!

 

All credit to www.instructables.com/id/The-Arduino-OctoSynth/

 

I cut individual keys from stripboard because I have fat "sausage" fingers - not for any technical reasons.

Digital logic sound generator using CMOS chips and run off 5 volts. Oscillators, logic gates, melody generators, sequencer, filter, etc.

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

Four oscillators, three multimode filters, two A/R envelope generators, digital gate sequencer, noise generator, phase shifter, external audio input...but no CV control. Uses mini-banana jacks. Built in 1977.

By the time I arrived in Germany (October 1955), the British troops were no longer an occupying force; but more in a defensive role of Western Europe. In the aftermath of the Berlin Airlift (1949) it became obvious that the Soviet troops were here to stay, and the Cold War was getting colder by the minute! Part of the defence at that time was a series of early-warning radar units strung along the East Germany border between the Danish border in the north and the American zone south of Hanover! Our unit at Lüneburg was one of them.

 

A design from Brooks Shera this takes the signal from an oven-controlled crystal oscillator and disciplines it via a pulse-per-second input. Normally the PPS is provided by a GPS receiver that is locked-on to the atomic clocks in the satellite constellation. In this case the PPS signal will be provided by the IBM master clock.

 

The disciplined 10MHz out will then be multiplied-up and used to clock an embedded PC.

 

Of course this PCB would benefit from some components, and I've started ordering them.

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

The beeper for the ringer consists of a piezo sounder and a little PCB containing a transistor oscillator.

1. Product Overview :

 

XT1511 side is a smart LED control circuit and light emitting circuit in one controlled LED source, which has the shape of a 4020 LED chip. Each lighting element is a pixel, and the intensities of the pixels are contained within the intelligent digital interface input. The output is driven by patented PWM technology, which effectively guarantees high consistency of the color of the pixels. The control circuit consists of a signal shaping amplification circuit, a built-in constant current circuit, and a high precision RC oscillator.

 

The data protocol being used is uni-polar NRZ communication mode. The 24-bit data is transmitted from the controller to DIN of the first element, and if it is accepted it is extracted pixel to pixel. After an internal data latch, the remaining data is passed through the internal amplification circuit and sent out on the DO port to the remaining pixels. The pixel is reset after the end of DIN. Using automatic shaping forwarding technology makes the number of cascaded pixels without signal transmission only limited by signal transmission speed.

The LED has a low driving voltage (which allows for environmental protection and energy saving), high brightness, scattering angle, good consistency, low power, and long life. The control circuit is integrated in the LED above.

 

2. Main Application Field:

 

●Full color LED string light, LED full color module, LED super hard and soft lights, LED guardrail tube, LED appearance / scene lighting

 

● LED point light, LED pixel screen, LED shaped screen, a variety of electronic products, electrical equipment etc..

  

3. Description:

 

●Top SMD internal integrated high quality external control line serial cascade constant current IC;

 

●control circuit and the RGB chip in SMD 4020 components, to form a complete control of pixel, color mixing uniformity and consistency;

 

●built-in data shaping circuit, a pixel signal is received after wave shaping and output waveform distortion will not guarantee a line;

 

●The built-in power on reset and reset circuit, the power does not work;

●gray level adjusting circuit (256 level gray scale adjustable);

 

●red drive special treatment, color balance;

 

●line data transmission;

 

●plastic forward strengthening technology, the transmission distance between two points over 10M;

 

●Using a typical data transmission frequency of 800 K bps, when the refresh rate of 30 frames per sec

  

if you have any interesting for it, please contact me:

 

My name is billy zhang, and My E-mail is bill_xt@Jercio.com

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

With the bias/erase oscillator PCB out of the way, the cassette hold-down lever can be removed.

Digital logic sound generator using CMOS chips and run off 5 volts. Oscillators, logic gates, melody generators, sequencer, filter, etc.

I visited here again this year (June 2012). Note the wavy hair!! Unfortunately, now mostly gone!!!

There's a third mode of local oscillator injection:

plate (anode) injection.

 

In an article entitled, "Frequency Changers", written by W. T. Cocking for the May 6th, 1931 edition of Wireless World magazine, Cocking cites

the need for minimization of local oscillator (LO) radiation from the

first mixer in a superhet which doesn't include an RF amplifier.

 

Cocking writes, "...The oscillator is coupled to the anode circuit of

the detector [i.e., mixer], which must be a screen-grid valve [i.e.,

vacuum tube]. If this valve is correctly chosen to have a small

grid-anode interelectrode capacity and it be properly screened,

there is no appreciable feed-back from the anode to the grid of

the detector [mixer]. [See Figure 5.]

 

The oscillator is isolated from the aerial circuit, therefore,

and as a result the circuit is free from radiation and can be

used with an outdoor aerial with impunity.

 

At first glance it might appear that coupling the oscillator

to the detector anode circuit would not give good results;

actually, however, it is more direct and logical than

coupling it to the grid circuit, and it is capable of quite as satisfactory operation.

 

It must be remembered that with anode-bend detection,

rectification takes place in the anode circuit, and

that the action of the valve can be considered as that

of an H.F. amplifier followed by a diode rectifier....

 

Since the local oscillations are not amplified by

the detector they must be stronger than is necessary

when they are fed into the grid circuit. This brings

no difficulties in its train, as it is only necessary

to apply a somewhat higher H.T. [B+] voltage to the

oscillator and to couple it more closely to the

detector.

 

This close coupling allows of a simplification of

the circuit by omitting the coupling coil, and

including the tuned-anode coil of the oscillator

directly in the detector anode circuit as in

Fig. 6.

 

In this manner the waveband switching is very

considerably simplified, while the coil

construction becomes no different from that of

the ordinary reacting detector...."

 

Oscillator Temple (CH)

––––––––––––––––––

SWISS PSYCH FEST 2013

18.05.2013

@ Amalgame Club

Yverdon-les-Bains

Switzerland

 

Jeremy Küng ©

mon portfolio

mes photos

The first thing was to solder the IC socket for the oscillator (HEF40106BP) in place on the veroboard.

ILIOS live at the Athens Biennale: "Symphony for electronics and internal combustion engine vibrations", June 27th, 2009

www.siteilios.gr

Here you can see that I replaced the LM741 CV summing amps with LT1006s in Millmax sockets. Slow devices, but with insanely low offset voltages.

Kassette (CH)

––––––––––––––––––

SWISS PSYCH FEST 2013

18.05.2013

@ Amalgame Club

Yverdon-les-Bains

Switzerland

 

Jeremy Küng ©

mon portfolio

mes photos

Digital logic sound generator using CMOS chips and run off 5 volts. Oscillators, logic gates, shift register, etc.

I like how the smoke is in this picture, mind you I'm outdoors. Anyway, this is a cool setup. I'm using some home made gear here. In the foreground is a wavetable oscillator/sequencer ina suitcase and an analog sequencer console.

Stereolab (2019 Tour) @ 9:30 Club, Washington, DC on Wednesday, September 25, 2019.

 

#Tour #Setlist:

 

Brakhage

French Disko

Double Rocker

Miss Modular

Vonal Declosion

Metronomic Underground

Need to Be

Come and Play in the Milky Night

Anamorphose

Ping Pong

Percolator

Lo Boob Oscillator

 

Encore:

Rainbo Conversation

Crest

The Extension Trip

built this from a $4 kit and added ability to tune it via pots.

In the lab we sometimes have an oscillator at one frequency and need to create another oscillator at some fixed multiple of that frequency. For instance, at LLO we have a 24.484150 MHz oscillator and we also need an oscillator at exactly 5/2 times that frequency.

 

I was wondering how this was done. I looked inside the box and saw a "frequency multipler" (×5) connected to a "frequency divider" (÷2). Huh.

 

I asked Hartmut how these things work, and as an example he sketched something resembling this figure.

 

Recursion always seems clever, and even moreso in electronics (where it typically goes by the name "feedback".) Here we have a box that takes in a signal at frequency 2f and produces a signal at half that frequency, 1f.

 

How does it do that?

 

Well, pretend that it's already doing it. Then we can take the 1f output and mix (multiply) it by the 2f input. When you multiply two sinusoids, you get a signal containing sinusoids at the sum and the difference of the original frequencies.

 

So mixing 1f and 2f gives us a signal containing 1f and 3f. Low pass filter and keep the 1f. Done! You have frequency divider.

 

How this thing is bootstrapped--what it does when you first turn it on--I don't know.

 

Similar tricks get you other multiples of the original frequency. For instance, here we could insert a tap before the low pass filter and get 3f as an output.

We made an oscillator using a single active component, the 2N6027 programmable unijunction transistor (PUT). Photo by David Henshall.

Broken, damaged, spent... but I hope good for stack - thermoacoustic oscillator.

Mystery BFO-- this view shows the slug-tuned oscillator coil and one (the only one!) Black Beauty capacitor which may need replacement.

Just some more "work" things. This machine looks AND sounds horrible to parents... but it helps keep babies alive. If anyone is wondering, this is a high frequency oscillatory ventilator.

1. Product Overview :

SK6805-2427 is a smart LED control circuit and light emitting circuit in one controlled LED source,

which has the shape of a 5050 LED chip. Each lighting element is a pixel, and the intensities of the

pixels are contained within the intelligent digital interface input. The output is driven by patented

PWM technology, which effectively guarantees high consistency of the color of the pixels. The

control circuit consists of a signal shaping amplification circuit, a built-in constant current circuit,

and a high precision RC oscillator.

First wave of modular, all ziplocked nice and snug, ready to be attacked by red hot pokers...

@ "Feira da Vandoma" Oporto, Portugal

 

Co-founder of the great experimental duo of crazy musicians/performers "Calhau!"

 

About the project "Calhau!":

"Under the name of Calhau! and other capricious derivations, the Porto-based couple, Marta Ângela and João Alves, have produced a remarkable body of cross-disciplinary work since 2006 in visual arts, film and music -- silkscreens, musical instruments, texts, wardrobes and characterisation, public presentation of films, concerts, performances and lectures -- highlighting a fascination for the "sometimes esoteric elitism of certain manifestations of (rural) popular culture". Accepted as seductively bizarre in the world of independent music and considered as ethically compromised with humor and 'craft experts in contingency' in the field of visual arts, their work is always bold and pertinent." (from culturgest.pt description)

 

A Film (Excerpt) by Calhau!:

www.youtube.com/watch?v=KakatyigLDQ

 

Interview with "Calhau!":

www.youtube.com/watch?v=kzQQCFFqDXw&feature=youtu.be

 

Homepages:

einsteinvoncalhau.com/

voncalhau.bandcamp.com/

www.flickr.com/photos/voncalhau

1. Product Overview :

SK6805-2427 is a smart LED control circuit and light emitting circuit in one controlled LED source,

which has the shape of a 5050 LED chip. Each lighting element is a pixel, and the intensities of the

pixels are contained within the intelligent digital interface input. The output is driven by patented

PWM technology, which effectively guarantees high consistency of the color of the pixels. The

control circuit consists of a signal shaping amplification circuit, a built-in constant current circuit,

and a high precision RC oscillator.

1 2 ••• 31 32 34 36 37 ••• 79 80