View allAll Photos Tagged modification
Hand trolley modified as bike trailer?
I guess the plastic container bucketing the seat acts as a mudguard? (there's potential for some more storage there - but this owner had completely cut away the front - possibly to allow pedalling!)
DADAMACHINIMA ►► avant-garde videogame modification
DADAMACHINIMA explores tactics of emergent gameplay, disrupted modes of interactivity,
and brute-force hacks of contemporary (video)game interfaces and environments.
exhibition December 18th - March 1st
Joan Leandre, Marc van Elburg, Julian Oliver, Gordan Savicic, Ludic Society, Gottfried Haider, JODI, Walter Langelaar, Aram Bartholl, Paul B. Davis, Friedrich Kirschner
PLANETART Volkskrantgebouw AMSTERDAM
dadamachinima.net
Photo taken by Richard Pyrker copyright richard.pyrker.com
A series of photos taken in and around the Wholesale District of Downtown Los Angeles, CA. This series attempts to create a portrait of the area through an examination of the architecture and other man-made "modifications" to the area.
I modified my Raspberry Pi by removing S2 (the so-far unused DSI video connector) and installing a right-angle connector in P5. This gives me easy access to 4 more I/O pins.
Removing S2 didn’t occur without scuffing up the board very slightly. Should anyone want to try it themselves, the trick is to gently pry the plastic of S2 off the pins. It will slide up/off, allowing one to remove the pins individually.
It's hard to see, but I didn’t sit P5 flat against the board. This is for two reasons: 1) The key-tab on some cable ends would have made it impossible to slide on otherwise and 2) That pesky C5 is hiding underneath and I didn’t want to inadvertently scrape it off.
Nach yang ini dari ALAM GAIB..
hasil pertapaan di gunung Merapi bareng Mbah Marijan..
ROSO...ROSO..ROSO...
Getting ready to cut the top out of the case to fit the Black Ice SR1 480mm radiator in - the stock case fits a 360mm radiator but since I'm removing the optical drive bay it makes sense to go 480mm.
Hasselblad Flexbody (V lens mount) modified for large format lenses and digital backs such as CFV 50C/100C
With smallrig handle and lightmeter
Show your artwork and portfolio works to the world. If you have talents on photography or graphic designing you can use this wordpress theme for free and can create your own website to show the world your passion. Check this out
allaboutbasic.com/2018/04/15/theme-sketch-by-automattic-a...
_____
Was in Toronto for the New Years festivities and picked up a job shooting a couple of friends new shop in town! Centerline motorsports is going to be specializing in custom fabrications, and automotive modification. Expect to see a part 2 to this shoot as more develops over there for the boys!
------------------------------------------------
Camera Info:
Canon 5Dc
Canon 20-35mm F2.8L
1x430exII Bounced/Diffused
------------------------------------------------
Use magnet to store chuck key.
These magnets were taken out of an abandoned hard drive which, like most things i deal with, was found on the streets for free.
www.cheaphack.net/2008/03/my-minilathe-and-several-mods-t...
Custom IBook I'm working on. Custom Black Paintjob on the inside of the clear plastic/acrylic casing, apple logos stripped out and backlit.... inside shielding removed so when the case is open the inside is see through, so you can see the inside electronics... Upgraded Hardrive, ram, soon to be overclocked and fedora core 7 linux installed.
Removing the spring was a dangerous business done at arms length with a long screw driver and safety goggles. Perhaps I should have put the camera down too :)
Needless to say it ended up halfway down the garage narrowly missing my nice new headlamps
Further stick modifications courtesy of Evilstevie. This is a Jessops clamp attached to the stick so that rather than fumbling one-handedly with my bag on a mosey about, I can just push down the lens cover and I'm set up, on a tripod (well, monopod) ready to go for reasonably steady pictures.
StickCam can also be applied to my elbow crutches or wheelchair, and is removed for non-camera occasions.
When I'm next up to having a little walk at night, we might see what pictures are like if combined with my StickLights...
(this pic taken by Evilstevie)
Honda Pilot Body Style Change 2015 Destop Wallpapers, 1600 x 1200, 215 KB
Honda Pilot Body Style Change 2015 HD wallpapers
wallpaperscene.com/cars/honda-pilot-body-style-change-201...
Had to plug up the old headlight mounting points, which included trying to reconstruct part of the smokebox door. Also made a new feedwater heater since the old one was poorly done and had to be removed when removing the cowling around the smokestack.
The smoke deflectors are out of place for access during modeling and painting, I didn't want to move them unnecessarily just to take a picture.
The general trend for quickly solving the problem with the intake elbow is to cut off the flexible part and install it back to front. this solves the clearance issue but now it has to point down as the TPS connector is in the way if you point it to the back of the car. The rocker cover breather pipe easily connects to the first of the two holes but the connection to the ICV is too short so I'll lengthen that hose with some 22mm copper pipe.
Where to put the MAF and the cone air filter will be a challenge too. lots of people either go down and through to the passenger footwell or take a feed from above the rad. My plan is to pop the whole lot down in the area that the alternator originally went leaving the rear of the engine bay for fuel and coolant stuff