View allAll Photos Tagged functional,
As the TIE-Striker is the only ship from the TIE-series with articulated solar panels so far, it was very important to me, to include that function into my MOC.
The access to change the wings position from upward to horizontal position is hidden underneath the pilot cockpit hatch.
By rotating a technic axle, the wings go up and down and will stay in any position you stop the movement.
Off course the wing still can move in its set positino when turning the TIE-Striker around. That function works best when the TIE-Striker rests on its stand, as the wings are quit heavy for the little mechanism to get moved (but it´s still possible without the stand).
All of the technic is hidden inside the tiny space between the pilot and bombardier cockpit.
The technic beam to lift the wings up and down is located right under the wings to maintain the cylindrical design of the cockpit pod.
It was a real hard chanllange to get the wings move to in the right angles and more than that to include all of the technic nearly invisible inside the pod.
I hope you like it!
Pages from a vintage dictation book - machine quilted with fabric / ripped paper bag and twine wrapped over glazed acrylic canvas.
(7" x 9")
Some background:
The VF-1 was developed by Stonewell/Bellcom/Shinnakasu for the U.N. Spacy by using alien Overtechnology obtained from the SDF-1 Macross alien spaceship. Its production was preceded by an aerodynamic proving version of its airframe, the VF-X. Unlike all later VF vehicles, the VF-X was strictly a jet aircraft, built to demonstrate that a jet fighter with the features necessary to convert to Battroid mode was aerodynamically feasible. After the VF-X's testing was finished, an advanced concept atmospheric-only prototype, the VF-0 Phoenix, was flight-tested from 2005 to 2007 and briefly served as an active-duty fighter from 2007 to the VF-1's rollout in late 2008, while the bugs were being worked out of the fully functional VF-1 prototype (the VF-X-1).
Introduced in 2008, the VF-1 would be produced en masse within a short period of time, a total of 5,459 airframes were delivered until 2013. The space-capable VF-1's combat debut was on February 7, 2009, during the Battle of South Ataria Island - the first battle of Space War I - and remained the mainstay fighter of the U.N. Spacy for the entire conflict. From the start the VF-1 proved to be an extremely capable and versatile craft, successfully combating a variety of Zentraedi mecha even in most sorties which saw UN Spacy forces significantly outnumbered. The versatility of the Valkyrie design enabled the variable fighter to act as both large-scale infantry and as air/space superiority fighter. The signature skills of U.N. Spacy ace pilot Maximilian Jenius exemplified the effectiveness of the variable systems as he near-constantly transformed the Valkyrie in battle to seize advantages of each mode as combat conditions changed from moment to moment.
The basic VF-1 was deployed in four sub-variants (designated A, D, J, and S) and its success was increased by continued development of various enhancements and upgrades, including the GBP-1S "Armored" Valkyrie, FAST Pack "Super" Valkyrie and the additional RÖ-X2 heavy cannon pack weapon system for the VF-1S with additional firepower. The FAST Pack system was designed to enhance the VF-1 Valkyrie variable fighter, and the initial V1.0 came in the form of conformal pallets that could be attached to the fighter’s leg flanks for additional fuel – primarily for Long Range Interdiction tasks in atmospheric environment. Later FAST Packs were designed for space operations.
After the end of Space War I, production on Earth was stopped but the VF-1 continued to be manufactured both in the Sol system and throughout the UNG space colonies. Although the VF-1 would be replaced in 2020 as the primary Variable Fighter of the U.N. Spacy by the more capable, but also much bigger, VF-4 Lightning III, a long service record and its persistent production after the war in many space sectors proved the lasting worth of the design.
The versatile aircraft underwent constant upgrade programs. For instance, about a third of all VF-1 Valkyries were upgraded with Infrared Search and Track (IRST) systems, placed in a small, streamlined fairing in front of the cockpit. This system allowed passive long-range search and track modes, freeing the pilot from the need to give away his/her position through active radar emissions. The sensor could also be used for target illumination and precision weapons guidance.
Many Valkyries also received improved radar warning systems, with sensor arrays mounted on the wingtips, the fins and/or on the LERXs. Improved ECR measures and other defensive measure like flare/chaff dispensers were also added to some machines, typically in conformal fairings on the flanks of the legs/engine pods.
In early 2011, VF-1 production on Earth had already reached the 2.500th aircraft, a VF-1J which received a striking white-and-blue commemorative paint scheme upon roll-out, decorated with the logos of all major manufacturers and system suppliers. After a brief PR tour the machine (Bu. No. 2110406/1) was handed over to SVF-1, the famous Skull Squadron, as an attrition replacement for Major Yingluck 'Joker' Maneethapo's aircraft, leader of the unit’s 5th Flight and a Thai pilot ace from the first stages of the Zentraedi attacks in 2009.
With the opportunity to add more personal style to his new mount, Maneethapo's chose the non-standard modex ML 555 for his fighter - a play of words, because the five is pronounced 'ha' in Thai language and '555' a frequent abbreviation for 'laughing'. Bu. No. 2110406/1 retained its bright PR livery, because its primary colors matched well with SVF-1 ‘Lazulite’ flight’s ID color. The aircraft just lost the sponsor logos and instead received full military markings and tactical codes, including the unit’s renowned skull icon and the characteristic “ML” letter code on the foldable fins. The nose art for the 2.500th production VF-1 jubilee was retained, though.
In SVF-1 service, Bu. No. 2110406/1 was soon upgraded with an IRST and retrofitted with FAST Packs and avionics for various zero-G weapons for operations in space, since the unit was supposed to become based on SDF-1 and go into space with the large carrier ship. However, only SVF-1's Flight #1, 2 and 3 were taken on board of the SDF-1 when the ship left Earth, the remaining unit parts remained at the home base on Ataria Island, tasked with homeland defense duties.
In 2012, at the end of the war, SVF-1’s Lazulite’ flight was re-located on board of ARMD-02 (Armaments Rigged-up Moving Deck Space Carrier vessel), which was and rebuilt and attached to the refitted SDF-1 Macross as originally intended. There, Bu. No. 2110406/1 served into the first year of the New Era 0001 in 2013, when it was replaced as a Flight Leader’s mount by a VF-4 and handed over to SVF-42 back on Earth, where it was repainted in standard U.N. Spacy fighter colors (even though it still retained its commemorative nose art) and served until 2017. Bu. No. 2110406/1 was then retired and unceremoniously scrapped, having already exceeded its expected service life.
The VF-1 was without doubt the most recognizable variable fighter of Space War I and was seen as a vibrant symbol of the U.N. Spacy. At the end of 2015 the final rollout of the VF-1 was celebrated at a special ceremony, commemorating this most famous of variable fighters. The VF-1 Valkryie was built from 2006 to 2013 with several major variants (VF-1A = 5,093, VF-1D = 85, VF-1J = 49, VF-1S = 30), sub-variants (VF-1G = 12, VE-1 = 122, VT-1 = 68) and upgrades of existing airframes (like the VF-1P).
Despite its relatively short and intense production run the fighter remained active in many second line units and continued to show its worthiness even years later, e. g. through Milia Jenius who would use her old VF-1 fighter in defense of the colonization fleet - 35 years after the type's service introduction!
General characteristics:
All-environment variable fighter and tactical combat Battroid,
used by U.N. Spacy, U.N. Navy, U.N. Space Air Force and U.N.S. Marine Corps
Accommodation:
Pilot only in Marty & Beck Mk-7 zero/zero ejection seat
Dimensions:
Fighter Mode:
Length 14.23 meters
Wingspan 14.78 meters (at 20° minimum sweep)
Height 3.84 meters
Battroid Mode:
Height 12.68 meters
Width 7.3 meters
Length 4.0 meters
Empty weight: 13.25 metric tons
Standard T-O mass: 18.5 metric tons
MTOW: 37.0 metric tons
Power Plant:
2x Shinnakasu Heavy Industry/P&W/Roice FF-2001 thermonuclear reaction turbine engines, output 650 MW each, rated at 11,500 kg in standard or 225.63 kN in overboost
4x Shinnakasu Heavy Industry NBS-1 high-thrust vernier thrusters (1 x counter reverse vernier thruster nozzle mounted on the side of each leg nacelle/air intake, 1 x wing thruster roll control system on each wingtip)
18x P&W LHP04 low-thrust vernier thrusters beneath multipurpose hook/handles
Performance:
Battroid Mode: maximum walking speed 160 km/h
Fighter Mode: at 10,000 m Mach 2.71; at 30,000+ m Mach 3.87
g limit: in space +7
Thrust-to-weight ratio: empty 3.47; standard T-O 2.49; maximum T-O 1.24
Design Features:
3-mode variable transformation; variable geometry wing; vertical take-off and landing; control-configurable vehicle; single-axis thrust vectoring; three "magic hand" manipulators for maintenance use; retractable canopy shield for Battroid mode and atmospheric reentry; option of GBP-1S system, atmospheric-escape booster, or FAST Pack system
Transformation:
Standard time from Fighter to Battroid (automated): under 5 sec.
Min. time from Fighter to Battroid (manual): 0.9 sec.
Armament:
2x Mauler RÖV-20 anti-aircraft laser cannon, firing 6,000 ppm
1x Howard GU-11 55 mm three-barrel Gatling gun pod with 200 RPG, fired at 1,200 rpm
4x underwing hard points for a wide variety of ordnance, including…
12x AMM-1 hybrid guided multipurpose missiles (3/point), or
12x MK-82 LDGB conventional bombs (3/point), or
6x RMS-1 large anti-ship reaction missiles (2/outboard point, 1/inboard point), or
4x UUM-7 micro-missile pods (1/point) each carrying 15 x Bifors HMM-01 micro-missiles,
or a combination of above load-outs
The kit and its assembly:
Another small and vintage 1:100 VF-1 Fighter. This time it’s a non-canonical aircraft, based on a limited edition decal sheet that was published with the Japanese Model Graphix magazine in April 2001 (check this here for reference: www.starshipmodeler.com/mecha/jl_clrvalk.htm) with Hasegawa’s first release of their 1:72 Valkyrie Fighter kit. The give-away sheet featured several VF-1s, including an anniversary paint scheme for the 2.500th production Valkyrie. This is AFAIK neither ‘official’ nor canonical – but the pretty blue-and-white livery caught my attention, and I had for a long time the plan to re-create this livery on one of my favored 1:100 models. This would not work 100%, though, so I had to improvise – see below.
The kit was built OOB, with the landing gear down and (after taking the flight scenic pictures) with an open canopy, mounted on a small lift arm. Some typical small blade antennae the 1:100 simple kit lacks were added around the hull as a standard measure to improve the look. In the cockpit I added side consoles and a pilot figure for the in-flight shots.
The only non-standard additions are the IRST sensor fairing in front of the cockpit – the model of the anniversary VF-1 in the Model Graphix magazine carries this canonical upgrade, too, it was created from clear sprue material. Another tiny addition were the RHAWS antenna fairings at the top of the fins, scratched from small styrene profile bits.
The Valkyrie’s ordnance is standard and was taken OOB, featuring twelve AMM-1 missiles under the wings plus the standard GU-11 gatling gun pod; the latter was modified to hold a scratched wire display for in-flight pictures at its rear end. The Model Graphix VF-1 is insofar confusing as it seems to carry something that looks like a white ACMI pod on a non-standard pylon, rather attached to the legs than to the wings? That's odd and I could not make up a useful function, so I rejected this detail. The magazine Valkyrie's belly drop tank was - even though canonical, AFAIK - also not taken over to my later in-service status.
Painting and markings:
The more challenging part of the build, in two ways. First, re-creating the original commemorative livery would have called for home-made decals printed in opaque white for the manufacturers’ logos, something I was not able to do at home. So, I had to interpret the livery in a different way and decided to spin the aircraft’s story further: what would become of this VF-1 after its roll-out and PR event? In a war situation it would certainly be delivered quickly to a frontline unit, and since I had some proper markings left over, I decided to attach this colorful bird to the famous Skull Squadron, SVF-1, yet to a less glorious Flight. Since flight leaders and aces in the Macross universe would frequently fly VF-1s in individual non-standard liveries, sometimes even very bright ones, the 2,500th VF-1 could have well retained its catchy paint scheme.
The second part of the challenge: the actual paint job. Again, no suitable decals were at hand, so I had to re-create everything from scratch. The VF-1J kit I used thankfully came molded in white styrene, so that the front half of the aircraft could be easily painted in white, with no darker/colored plastic shining through. I painted the white (Revell 301, a very pure white) with a brush first. For the blue rear half, I settled upon an intense and deep cobalt blue tone (ModelMaster 2012). For the zigzag border between the colors, I used Tamiya masking tape, trimmed with a tailor’s zigzag scissors and applied in a slightly overlapping pattern for an irregular edge.
The landing gear became standard all-white (Revell 301, too), with bright red edges (Humbrol 174) on the covers. Antenna fairings were painted with radome tan (Humbrol 7) as small color highlights.
The cockpit interior became standard medium grey (Revell 47) with a black ejection seat with brown cushions (Humbrol 119 and Revell 84), and brown “black boxes” behind the headrest. The air intakes as well as the interior of the VG wings were painted dark grey (Revell 77). The jet nozzles/feet were internally painted with Humbrol 27003 (Steel Metallizer) and with Revell 91 on the outside, and they were later thoroughly treated with graphite to give them a burnt/worn look.
The GU-11 pod became standard bare metal (Revell 91, Iron metallic), the AMM-1s were painted in light grey (Humbrol 127) with many additional painted details in five additional colors, quite a tedious task when repeated twelve times...
After basic painting was one the model received a careful overall washing with black ink to emphasize the engraved panel lines, and light post-shading was done to the blue areas to emphasize single panels.
The full-color ’kite’ roundels came from an 1:100 VF-1A sheet, the skull emblems were left over from my Kotobukiya 1:72 VF-4 build some years ago, which OOB carries SVF-1 markings, too. The 2.500th aircraft nose art decoration was printed on clear decal film with an ink jet printer at home, even though it’s so small that no details can be discerned on the model. SVF-1’s “ML” tail code was created with single white decal letters (RAF WWII font), the red “555” modex came from an PrintScale A-26 Invader sheet, it's part of a USAF serial number from an all-black Korean War era aircraft.
The wings' leading edges were finished in medium grey, done with decal sheet material. The Model Graphix Valkyrie does not sport this detail, but I think that the VF-1 looks better with them and more realistic. Red warning stripes around the legs - also not seen on the model in the magazine - were made from similar material.
The confetti along the jagged edge between the white and the blue areas was created with decal material, too – every bit was cut out and put into place one for one… To match the cobalt blue tone, the respective enamel paint was applied on clear decal sheet material and cut into small bits. For the white and red confetti, generic decal sheet material was used. All in all, this was another tedious process, but, at the small 1:100 scale, masks or tape would have been much more complex and less successful with the brushes I use for painting. For this home-made approach the result looks quite good!
Finally, after some typical details and position lights had been added with clear paints over a silver base, the small VF-1 was sealed with a coat of semi-matt acrylic varnish, giving it a slightly shiny finish.
A pretty VF-1 – even though I’d call it purely fictional, despite being based on material that was published in a Japanese magazine more than 20 years ago. The simple yet striking livery was a bit tricky to create, but the result, with the additional SVF-1 unit markings, looks good and makes me wonder how this machine would look with FAST pack elements for use in space or as a transformed Battroid?
These chairs weren't part of an exhibit; they were scattered all over the courtyard and are actual seating. Every chair has a designer behind it, though. Even when everyone's too distracted by the gigantic steel Serra sculpture in front of them to notice.
Since they're just, y'know, seating, these weren't labelled or any such thing, but I believe that they are Bertoia side chairs, by Harry Bertoia, designed in 1952. The chairs are made of welded steel rods and have a powder-coat finish.
If they are not Bertoias, they are very good imitations of them. However, since this is MoMA, I'm inclined to believe that they're the real deal.
The 1928 Ford Model A was a typical donor car for the development of the early Harry Miller Race cars. Such items included the steering box, axles, differential, springs, and the transmission; although most were highly modified for racing.
In this model, the miniature Offy engine was scaled from drawings of the full-size engine and sports Ron’s custom made Winfield carburetors. Ron says it runs best on E-85 Ethanol and spark ignition. Stainless steel was used to fabricate almost everything except the engine, transmission, differential, rims, and body. The model has functional gauges, pedals for the accelerator and brakes, shift lever for forward and reverse, and an external hand brake. The hand pump pressurizes the fuel tank that is located behind the driver’s seat and the lubrication is via dry sump with the oil tank located between the driver and engine. Also it is equipped with steering, leaf spring suspension, friction shocks, and Ron’s custom-made spoke and splined knockoff wheels
Ron built this model as a tribute to his Father who owned and raced the full-size car in the mid 1920s. It is almost exact- even down to the numbers and lettering on the body. Except for the engine Ron fabricated everything from memory and a few family photos of his Dad’s race car. This model measures 32 inches long, 16 inches wide, 13 inches high, and weighs 25 pounds.
See Another View of This Car at: www.flickr.com/photos/15794235@N06/42872928132/in/photost...
See More Tether Cars, RC Cars, and Engines at: www.flickr.com/photos/15794235@N06/sets/72157645118796544/
See More Inline Engines at: www.flickr.com/photos/15794235@N06/sets/72157638336677194/
See Our Model Engine Collection at: www.flickr.com/photos/15794235@N06/sets/72157602933346098/
Visit Our Photo Sets at: www.flickr.com/photos/15794235@N06/sets
Courtesy Paul and Paula Knapp
Miniature Engineering Museum
170636 passes the bland Portakabin style Stonea signal box on 3rd October 2024 with 1N53 1200 Cambridge to Birmingham New Street.
The original 1883 box was behind where the train is, and was demolished in 1984 - replaced by the monstrosity on the left.
Pole shot.
Wallpaper: i.imgur.com/ztJCpBi.jpg
Clock/Date: Elegance - www.deviantart.com/download/244373054/rainmeter___eleganc...
Sidebars/Taskbar Items: Enigma - github.com/downloads/Kaelri/Enigma/Enigma4Patch1.rmskin
List: Mediterranean Defense - www.mediafire.com/download/jpmgml84diyg1jf/Animus-BlackRo...
Do I Need A Jacket?: DINAJ - www.deviantart.com/download/264544648/do_i_need_a_jacket_...
Hide Taskbar: MagicTaskbar - rocketdock.com/addon/misc/3425
Game Launcher: Launcher - dl.dropboxusercontent.com/u/11502656/Rainmeter/gamelaunch...
When it comes to the Game Launcher, you'll need to edit to suit your games/images.
Here's some code from the skin for example - i.imgur.com/rxQ9r0p.jpg
The first studio that I worked out of in San Francisco received more foot traffic than where I did my work in Lothian, Maryland. As I was finishing my first hedgehog tea set, I received a request by somebody who saw the tea set in progress. This woman asked if I would be able to make a small planter the size of one of the teacups. I quickly made one, but lost the information of the person who requested it. I ended up quickly selling the prototype to somebody else and have been perfecting the idea ever since, just in case I find this customer again. #animal #wildlife #wild #planter #trivet #planting #plant #green #growing #living #peperomia #pottedplant #potting #clay #ceramic #stoneware #pottery #sculpture #handmade #wheel #wheelthrown #hedgehog #hedgie #functional #home #upsidedown
non-functional teapot.
porcelain, red iron oxide, clear glaze, nichrome wire. fired to cone 10 reduction.
This particular windmill isn't functional (although I think it's photogenic), the typical windmill for pumping water has a wheel, gearbox and tail mounted on top of a tower. The wheel is connected to a gearbox which converts rotary motion into vertical motion for pumping. The tail is offset from the wheel shaft to allow the tail to fold parallel to the wheel in high wind conditions and effectively shut-down the mill and prevent destruction or damage due to high winds. The drive shaft rotated by the wheel connects to the gearbox converting rotary motion into vertical motion for pumping water.
F225 universal agricultural tractor as of 1962. Includes two cylinder engine, two speed transmission, drive shafts, working steering, lifting arrangement. Can be configured as tipper, front loader with digger or fork. There was also a sowing machine and a mower for it.
The design and modular functionality of this set is unparalleled. The two cockpits detached from the center leaving a base behind. The top two sections also detached and could be reattached to the cockpits creating two ships with a little finagling of the tires. There was so much that you could do with this set. I toyed around (pun intended) with doing a whole Febrovery month based on this single set….but I figured I would wait for a 28 day Febrovery for that. This set is a perfect companion to the Alien Moon Stalker released the following year. I love the color scheme on both of them.
Tutorial on Instructables: www.instructables.com/id/Functional-LEGO-Nutcrackers/
With a simple pull of the lever, these decorative figures can open and close their jaws like authentic nutcrackers!
Both of these models were built in the recent weeks leading up to Christmas. The design was pretty straightforward, but two major issues were making the faces look good, and finally getting the hats right. In fact, the green nutcracker's crown took the longest to figure out, and was finally made with hinge plates.
As mentioned in the tutorial, although these can in fact function as real nutcrackers, they're somewhat rickety and best suited for holiday decorations.
This is from mid summer (I finished the car 2 days before I left for college). It gives you an idea of what can be done in 1.5 months when you're really committed to something.
The more common sighting of this incredibly powerful coupe. The functional air spoiler is tastefully done.
BOX DATE: 1992
MANUFACTURER: Mattel
SPECIAL FEATURES: Fold out wall; storage compartments in table, bed, and benches; light up lamp post; hidden compartment in picture above fireplace
PERSONAL FUN FACT: This living room was probably my favorite interior portion of the house. Growing up, I was fascinated by the hidden storage above the fireplace. Of course, you really can't fit much of anything in this super narrow compartment. This is why the accessories sold with the Fold 'n Fun House were so small and compact (if they were sized normally, they wouldn't fit inside the storage areas of the house). The little fireplace makes the room ever so cozy. I love how there is even an image of stacked firewood to the left. Although pink was never my favorite color, especially when it came to doll furniture, I do think that this vibrant pink makes the house feel that much more magical. The coffee table fits inside the fireplace for storage, and the bench folds up against the wall. I had both of these pieces with my original house, however they are no longer functional. Somewhere along the line, I lost one of the legs to the coffee table (perhaps it broke). While I still have all three benches that I got growing up, none stand up properly anymore due to old age and way too much use. That's why I was so glad that the house photographed here, which was purchased in 2018 at a charity store, was so complete!
The EOS M3 is a great camera for existing Canon enthusiasts and casual videographers alike. The autofocus performance continues to impress.
Harley-Davidson, Inc. (H-D), or Harley, is an American motorcycle manufacturer, founded in Milwaukee, Wisconsin in 1903.
As one of two major American motorcycle manufacturers to survive the Great Depression (along with Indian), the company has survived numerous ownership arrangements, subsidiary arrangements (e.g., Aermacchi 1974-1978 and Buell 1987-2009), periods of poor economic health and product quality, as well as intense global competition — to become one of the world's largest motorcycle manufacturers and an iconic brand widely known for its loyal following — with owner clubs and events worldwide as well as a company sponsored brand-focused museum.
Noted for a style of customization that gave rise to the chopper motorcycle style, Harley-Davidson traditionally marketed heavyweight, air-cooled cruiser motorcycles with engine displacements greater than 700 cm³ — and has broadened its offerings to include its more contemporary VRSC (2002) and middle-weight Street (2015) platforms.
Harley-Davidson manufactures its motorcycles at factories in York, Pennsylvania; Milwaukee, Wisconsin; Kansas City, Missouri; Manaus, Brazil; and Bawal, India — and markets its products worldwide.
Besides motorcycles, the company licenses and markets merchandise under the Harley-Davidson brand, among them being apparel, home decor and ornaments, accessories, toys, and scale figures of its motorcycles, and video games based on its motorcycle line and the community.
HISTORY
BEGINNING
In 1901, 20-year-old William S. Harley drew up plans for a small engine with a displacement of 7.07 cubic inches (116 cc³) and four-inch (102 mm) flywheels. The engine was designed for use in a regular pedal-bicycle frame. Over the next two years, Harley and his childhood friend Arthur Davidson worked on their motor-bicycle using the northside Milwaukee machine shop at the home of their friend, Henry Melk. It was finished in 1903 with the help of Arthur's brother, Walter Davidson. Upon testing their power-cycle, Harley and the Davidson brothers found it unable to climb the hills around Milwaukee without pedal assistance. They quickly wrote off their first motor-bicycle as a valuable learning experiment.
Work immediately began on a new and improved second-generation machine. This first "real" Harley-Davidson motorcycle had a bigger engine of 24.74 cubic inches (405 cc³) with 9.75 inches (25 cm) flywheels weighing 28 lb (13 kg). The machine's advanced loop-frame pattern was similar to the 1903 Milwaukee Merkel motorcycle (designed by Joseph Merkel, later of Flying Merkel fame). The bigger engine and loop-frame design took it out of the motorized bicycle category and marked the path to future motorcycle designs. The boys also received help with their bigger engine from outboard motor pioneer Ole Evinrude, who was then building gas engines of his own design for automotive use on Milwaukee's Lake Street.
The prototype of the new loop-frame Harley-Davidson was assembled in a 10 ft × 15 ft (3.0 m × 4.6 m) shed in the Davidson family backyard. Most of the major parts, however, were made elsewhere, including some probably fabricated at the West Milwaukee railshops where oldest brother William A. Davidson was then toolroom foreman. This prototype machine was functional by September 8, 1904, when it competed in a Milwaukee motorcycle race held at State Fair Park. It was ridden by Edward Hildebrand and placed fourth. This is the first documented appearance of a Harley-Davidson motorcycle in the historical record.
In January 1905, small advertisements were placed in the Automobile and Cycle Trade Journal offering bare Harley-Davidson engines to the do-it-yourself trade. By April, complete motorcycles were in production on a very limited basis. That year, the first Harley-Davidson dealer, Carl H. Lang of Chicago, sold three bikes from the five built in the Davidson backyard shed. Years later the original shed was taken to the Juneau Avenue factory where it would stand for many decades as a tribute to the Motor Company's humble origins until it was accidentally destroyed by contractors cleaning the factory yard in the early 1970s.
In 1906, Harley and the Davidson brothers built their first factory on Chestnut Street (later Juneau Avenue),[12] at the current location of Harley-Davidson's corporate headquarters. The first Juneau Avenue plant was a 40 ft × 60 ft (12 m × 18 m) single-story wooden structure. The company produced about 50 motorcycles that year.
In 1907, William S. Harley graduated from the University of Wisconsin–Madison with a degree in mechanical engineering. That year additional factory expansion came with a second floor and later with facings and additions of Milwaukee pale yellow ("cream") brick. With the new facilities production increased to 150 motorcycles in 1907. The company was officially incorporated that September. They also began selling their motorcycles to police departments around this time, a market that has been important to them ever since.
In 1907 William A. Davidson, brother to Arthur and Walter Davidson, quit his job as tool foreman for the Milwaukee Road railroad and joined the Motor Company.
Production in 1905 and 1906 were all single-cylinder models with 26.84 cubic inch (440 cm³) engines. In February 1907 a prototype model with a 45-degree V-Twin engine was displayed at the Chicago Automobile Show. Although shown and advertised, very few V-Twin models were built between 1907 and 1910. These first V-Twins displaced 53.68 cubic inches (880 cm³) and produced about 7 horsepower (5.2 kW). This gave about double the power of the first singles. Top speed was about 60 mph (100 km/h). Production jumped from 450 motorcycles in 1908 to 1,149 machines in 1909.
By 1911, some 150 makes of motorcycles had already been built in the United States – although just a handful would survive the 1910s.
In 1911, an improved V-Twin model was introduced. The new engine had mechanically operated intake valves, as opposed to the "automatic" intake valves used on earlier V-Twins that opened by engine vacuum. With a displacement of 49.48 cubic inches (811 cm³), the 1911 V-Twin was smaller than earlier twins, but gave better performance. After 1913 the majority of bikes produced by Harley-Davidson would be V-Twin models.
In 1912, Harley-Davidson introduced their patented "Ful-Floteing Seat", which was suspended by a coil spring inside the seat tube. The spring tension could be adjusted to suit the rider's weight. More than 3 inches (76 mm) of travel was available. Harley-Davidson would use seats of this type until 1958.
By 1913, the yellow brick factory had been demolished and on the site a new 5-story structure had been built. Begun in 1910, the factory with its many additions would take up two blocks along Juneau Avenue and around the corner on 38th Street. Despite the competition, Harley-Davidson was already pulling ahead of Indian and would dominate motorcycle racing after 1914. Production that year swelled to 16,284 machines.
WORLD WAR I
In 1917, the United States entered World War I and the military demanded motorcycles for the war effort. Harleys had already been used by the military in the Pancho Villa Expedition but World War I was the first time the motorcycle had been adopted for military issue, first with the British Model H, produced by British Triumph Motorcycles Ltd in 1915. After the U.S. entry into the war, the U.S. military purchased over 20,000 motorcycles from Harley-Davidson.
BICYCLES
Harley-Davidson launched a line of bicycles in 1917 in hopes of recruiting customers for its motorcycles. Besides the traditional diamond frame men's bicycle, models included a step-through frame 3-18 "Ladies Standard" and a 5-17 "Boy Scout" for youth. The effort was discontinued in 1923 because of disappointing sales.
The bicycles were built for Harley-Davidson in Dayton, Ohio, by the Davis Machine Company from 1917 to 1921, when Davis stopped manufacturing bicycles.
1920s
By 1920, Harley-Davidson was the largest motorcycle manufacturer in the world, with 28,189 machines produced, and dealers in 67 countries.
In 1921, a Harley-Davidson, ridden by Otto Walker, was the first motorcycle ever to win a race at an average speed greater than 100 mph (160 km/h).
During the 1920s, several improvements were put in place, such as a new 74 cubic inch (1,212.6 cm³) V-Twin, introduced in 1921, and the "teardrop" gas tank in 1925. A front brake was added in 1928 although notably only on the J/JD models.
In the late summer of 1929, Harley-Davidson introduced its 45 cubic inches (737 cm³) flathead V-Twin to compete with the Indian 101 Scout and the Excelsior Super X. This was the "D" model, produced from 1929 to 1931. Riders of Indian motorcycles derisively referred to this model as the "three cylinder Harley" because the generator was upright and parallel to the front cylinder. The 2.745 in (69.7 mm) bore and 3.8125 in (96.8 mm) stroke would continue in most versions of the 750 engine; exceptions include the XA and the XR-750.
GREAT DEPRESSION
The Great Depression began a few months after the introduction of their 45 cubic inch (737 cm³) model. Harley-Davidson's sales fell from 21,000 in 1929 to 3,703 in 1933. Despite this, Harley-Davidson unveiled a new lineup for 1934, which included a flathead engine and Art Deco styling.
In order to survive the remainder of the Depression, the company manufactured industrial powerplants based on their motorcycle engines. They also designed and built a three-wheeled delivery vehicle called the Servi-Car, which remained in production until 1973.
In the mid-1930s, Alfred Rich Child opened a production line in Japan with the 74-cubic-inch (1,210 cm³) VL. The Japanese license-holder, Sankyo Seiyaku Corporation, severed its business relations with Harley-Davidson in 1936 and continued manufacturing the VL under the Rikuo name.
An 80-cubic-inch (1,300 cm³) flathead engine was added to the line in 1935, by which time the single-cylinder motorcycles had been discontinued.
In 1936, the 61E and 61EL models with the "Knucklehead" OHV engines was introduced. Valvetrain problems in early Knucklehead engines required a redesign halfway through its first year of production and retrofitting of the new valvetrain on earlier engines.
By 1937, all Harley-Davidson's flathead engines were equipped with dry-sump oil recirculation systems similar to the one introduced in the "Knucklehead" OHV engine. The revised 74-cubic-inch (1,210 cm³) V and VL models were renamed U and UL, the 80-cubic-inch (1,300 cc³) VH and VLH to be renamed UH and ULH, and the 45-cubic-inch (740 cc³) R to be renamed W.
In 1941, the 74-cubic-inch (1,210 cm³) "Knucklehead" was introduced as the F and the FL. The 80-cubic-inch (1,300 cc³) flathead UH and ULH models were discontinued after 1941, while the 74 inch (1880 mm) U & UL flathead models were produced up to 1948.
WORLD WAR II
One of only two American cycle manufacturers to survive the Great Depression. Harley-Davidson again produced large numbers of motorcycles for the US Army in World War II and resumed civilian production afterwards, producing a range of large V-twin motorcycles that were successful both on racetracks and for private buyers.
Harley-Davidson, on the eve of World War II, was already supplying the Army with a military-specific version of its 45 cubic inches (740 cm³) WL line, called the WLA. The A in this case stood for "Army". Upon the outbreak of war, the company, along with most other manufacturing enterprises, shifted to war work. More than 90,000 military motorcycles, mostly WLAs and WLCs (the Canadian version) were produced, many to be provided to allies. Harley-Davidson received two Army-Navy ‘E’ Awards, one in 1943 and the other in 1945, which were awarded for Excellence in Production.
Shipments to the Soviet Union under the Lend-Lease program numbered at least 30,000. The WLAs produced during all four years of war production generally have 1942 serial numbers. Production of the WLA stopped at the end of World War II, but was resumed from 1950 to 1952 for use in the Korean War.
The U.S. Army also asked Harley-Davidson to produce a new motorcycle with many of the features of BMW's side-valve and shaft-driven R71. Harley largely copied the BMW engine and drive train and produced the shaft-driven 750 cc 1942 Harley-Davidson XA. This shared no dimensions, no parts and no design concepts (except side valves) with any prior Harley-Davidson engine. Due to the superior cooling of the flat-twin engine with the cylinders across the frame, Harley's XA cylinder heads ran 56 °C cooler than its V-twins. The XA never entered full production: the motorcycle by that time had been eclipsed by the Jeep as the Army's general purpose vehicle, and the WLA - already in production - was sufficient for its limited police, escort, and courier roles. Only 1,000 were made and the XA never went into full production. It remains the only shaft-driven Harley-Davidson ever made.
SMALL HARLEYS: HUMMERS AND AERMACCHIS
As part of war reparations, Harley-Davidson acquired the design of a small German motorcycle, the DKW RT 125, which they adapted, manufactured, and sold from 1948 to 1966. Various models were made, including the Hummer from 1955 to 1959, but they are all colloquially referred to as "Hummers" at present. BSA in the United Kingdom took the same design as the foundation of their BSA Bantam.
In 1960, Harley-Davidson consolidated the Model 165 and Hummer lines into the Super-10, introduced the Topper scooter, and bought fifty percent of Aermacchi's motorcycle division. Importation of Aermacchi's 250 cc horizontal single began the following year. The bike bore Harley-Davidson badges and was marketed as the Harley-Davidson Sprint. The engine of the Sprint was increased to 350 cc in 1969 and would remain that size until 1974, when the four-stroke Sprint was discontinued.
After the Pacer and Scat models were discontinued at the end of 1965, the Bobcat became the last of Harley-Davidson's American-made two-stroke motorcycles. The Bobcat was manufactured only in the 1966 model year.
Harley-Davidson replaced their American-made lightweight two-stroke motorcycles with the Aermacchi-built two-stroke powered M-65, M-65S, and Rapido. The M-65 had a semi-step-through frame and tank. The M-65S was a M-65 with a larger tank that eliminated the step-through feature. The Rapido was a larger bike with a 125 cc engine. The Aermacchi-built Harley-Davidsons became entirely two-stroke powered when the 250 cc two-stroke SS-250 replaced the four-stroke 350 cc Sprint in 1974.
Harley-Davidson purchased full control of Aermacchi's motorcycle production in 1974 and continued making two-stroke motorcycles there until 1978, when they sold the facility to Cagiva.
OVERSEAS
Established in 1918, the oldest continuously operating Harley-Davidson dealership outside of the United States is in Australia.[4] Sales in Japan started in 1912 then in 1929, Harley-Davidsons were produced in Japan under license to the company Rikuo (Rikuo Internal Combustion Company) under the name of Harley-Davidson and using the company's tooling, and later under the name Rikuo. Production continued until 1958.
TARNISHED REPUTATION
In 1952, following their application to the U.S. Tariff Commission for a 40 percent tax on imported motorcycles, Harley-Davidson was charged with restrictive practices.
In 1969, American Machine and Foundry (AMF) bought the company, streamlined production, and slashed the workforce. This tactic resulted in a labor strike and lower-quality bikes. The bikes were expensive and inferior in performance, handling, and quality to Japanese motorcycles. Sales and quality declined, and the company almost went bankrupt. The "Harley-Davidson" name was mocked as "Hardly Ableson", "Hardly Driveable," and "Hogly Ferguson", and the nickname "Hog" became pejorative.
In 1977, following the successful manufacture of the Liberty Edition to commemorate America's bicentennial in 1976, Harley-Davidson produced what has become one of its most controversial models, the Harley-Davidson Confederate Edition. The bike was essentially a stock Harley with Confederate-specific paint and details.
RESTRUCTING AND REVIVAL
In 1981, AMF sold the company to a group of 13 investors led by Vaughn Beals and Willie G. Davidson for $80 million. Inventory was strictly controlled using the just-in-time system.
In the early eighties, Harley-Davidson claimed that Japanese manufacturers were importing motorcycles into the US in such volume as to harm or threaten to harm domestic producers. After an investigation by the U.S. International Trade Commission, President Reagan imposed in 1983 a 45 percent tariff on imported bikes with engine capacities greater than 700 cc. Harley-Davidson subsequently rejected offers of assistance from Japanese motorcycle makers. However, the company did offer to drop the request for the tariff in exchange for loan guarantees from the Japanese.
Rather than trying to match the Japanese, the new management deliberately exploited the "retro" appeal of the machines, building motorcycles that deliberately adopted the look and feel of their earlier machines and the subsequent customizations of owners of that era. Many components such as brakes, forks, shocks, carburetors, electrics and wheels were outsourced from foreign manufacturers and quality increased, technical improvements were made, and buyers slowly returned.
Harley-Davidson bought the "Sub Shock" cantilever-swingarm rear suspension design from Missouri engineer Bill Davis and developed it into its Softail series of motorcycles, introduced in 1984 with the FXST Softail.
In response to possible motorcycle market loss due to the aging of baby-boomers, Harley-Davidson bought luxury motorhome manufacturer Holiday Rambler in 1986. In 1996, the company sold Holiday Rambler to the Monaco Coach Corporation.
The "Sturgis" model, boasting a dual belt-drive, was introduced initially in 1980 and was made for three years. This bike was then brought back as a commemorative model in 1991. By 1990, with the introduction of the "Fat Boy", Harley once again became the sales leader in the heavyweight (over 750 cm³) market. At the time of the Fat Boy model introduction, a story rapidly spread that its silver paint job and other features were inspired by the B-29; and Fat Boy was a combination of the names of the atomic bombs Fat Man and Little Boy. However, the Urban Legend Reference Pages lists this story as an urban legend.
1993 and 1994 saw the replacement of FXR models with the Dyna (FXD), which became the sole rubber mount FX Big Twin frame in 1994. The FXR was revived briefly from 1999 to 2000 for special limited editions (FXR2, FXR3 & FXR4).
Construction started on the $75 million, 130,000 square-foot (12,000 m2) Harley-Davidson Museum in the Menomonee Valley on June 1, 2006. It opened in 2008 and houses the company's vast collection of historic motorcycles and corporate archives, along with a restaurant, café and meeting space.
BUELL MOTORCYCLE COMPANY
Harley-Davidson's association with sportbike manufacturer Buell Motorcycle Company began in 1987 when they supplied Buell with fifty surplus XR1000 engines. Buell continued to buy engines from Harley-Davidson until 1993, when Harley-Davidson bought 49 percent of the Buell Motorcycle Company. Harley-Davidson increased its share in Buell to ninety-eight percent in 1998, and to complete ownership in 2003.
In an attempt to attract newcomers to motorcycling in general and to Harley-Davidson in particular, Buell developed a low-cost, low-maintenance motorcycle. The resulting single-cylinder Buell Blast was introduced in 2000, and was made through 2009, which, according to Buell, was to be the final year of production.
On October 15, 2009, Harley-Davidson Inc. issued an official statement that it would be discontinuing the Buell line and ceasing production immediately. The stated reason was to focus on the Harley-Davidson brand. The company refused to consider selling Buell. Founder Erik Buell subsequently established Erik Buell Racing and continued to manufacture and develop the company's 1125RR racing motorcycle.
FIRST OVERSEAS FACTORY IN BRAZIL
In 1998 the first Harley-Davidson factory outside the US opened in Manaus, Brazil, taking advantage of the free economic zone there. The location was positioned to sell motorcycles in the southern hemisphere market.
CLAIMS OF STOCK PRICE MANIPULATION
During its period of peak demand, during the late 1990s and early first decade of the 21st century, Harley-Davidson embarked on a program of expanding the number of dealerships throughout the country. At the same time, its current dealers typically had waiting lists that extended up to a year for some of the most popular models. Harley-Davidson, like the auto manufacturers, records a sale not when a consumer buys their product, but rather when it is delivered to a dealer. Therefore, it is possible for the manufacturer to inflate sales numbers by requiring dealers to accept more inventory than desired in a practice called channel stuffing. When demand softened following the unique 2003 model year, this news led to a dramatic decline in the stock price. In April 2004 alone, the price of HOG shares dropped from more than $60 to less than $40. Immediately prior to this decline, retiring CEO Jeffrey Bleustein profited $42 million on the exercise of employee stock options.[80] Harley-Davidson was named as a defendant in numerous class action suits filed by investors who claimed they were intentionally defrauded by Harley-Davidson's management and directors. By January 2007, the price of Harley-Davidson shares reached $70.
PROBLEMS WITH TOURING MODELS
Starting around 2000, several police departments started reporting problems with high speed instability on the Harley-Davidson Touring motorcycles. A Raleigh, North Carolina police officer, Charles Paul, was killed when his 2002 police touring motorcycle crashed after reportedly experiencing a high speed wobble. The California Highway Patrol conducted testing of the Police Touring motorcycles in 2006. The CHP test riders reported experiencing wobble or weave instability while operating the motorcycles on the test track.
2007 STRIKE
On February 2, 2007, upon the expiration of their union contract, about 2,700 employees at Harley-Davidson Inc.'s largest manufacturing plant in York, Pennsylvania went on strike after failing to agree on wages and health benefits. During the pendency of the strike, the company refused to pay for any portion of the striking employees' health care.
The day before the strike, after the union voted against the proposed contract and to authorize the strike, the company shut down all production at the plant. The York facility employs more than 3,200 workers, both union and non-union.
Harley-Davidson announced on February 16, 2007, that it had reached a labor agreement with union workers at its largest manufacturing plant, a breakthrough in the two-week-old strike. The strike disrupted Harley-Davidson's national production and was felt in Wisconsin, where 440 employees were laid off, and many Harley suppliers also laid off workers because of the strike.
MV AGUSTA GROUP
On July 11, 2008 Harley-Davidson announced they had signed a definitive agreement to acquire the MV Agusta Group for $109M USD (€70M). MV Agusta Group contains two lines of motorcycles: the high-performance MV Agusta brand and the lightweight Cagiva brand. The acquisition was completed on August 8.
On October 15, 2009, Harley-Davidson announced that it would divest its interest in MV Agusta. Harley-Davidson Inc. sold Italian motorcycle maker MV Agusta to Claudio Castiglioni, ending the transaction in the first week of August 2010. Castiglioni is the company's former owner and had been MV Agusta's chairman since Harley-Davidson bought it in 2008.
OPERATIONS IN INDIA
In August 2009, Harley-Davidson announced plans to enter the market in India, and started selling motorcycles there in 2010. The company established a subsidiary, Harley-Davidson India, in Gurgaon, near Delhi, in 2011, and created an Indian dealer network.
FINANCIAL CRISIS
According to Interbrand, the value of the Harley-Davidson brand fell by 43 percent to $4.34 billion in 2009. The fall in value is believed to be connected to the 66 percent drop in the company profits in two quarters of the previous year. On April 29, 2010, Harley-Davidson stated that they must cut $54 million in manufacturing costs from its production facilities in Wisconsin, and that they would explore alternative U.S. sites to accomplish this. The announcement came in the wake of a massive company-wide restructuring, which began in early 2009 and involved the closing of two factories, one distribution center, and the planned elimination of nearly 25 percent of its total workforce (around 3,500 employees). The company announced on September 14, 2010 that it would remain in Wisconsin.
MOTORCYCLE ENGINES
The classic Harley-Davidson engines are V-twin engines, with a 45° angle between the cylinders. The crankshaft has a single pin, and both pistons are connected to this pin through their connecting rods.
This 45° angle is covered under several United States patents and is an engineering tradeoff that allows a large, high-torque engine in a relatively small space. It causes the cylinders to fire at uneven intervals and produces the choppy "potato-potato" sound so strongly linked to the Harley-Davidson brand.
To simplify the engine and reduce costs, the V-twin ignition was designed to operate with a single set of points and no distributor. This is known as a dual fire ignition system, causing both spark plugs to fire regardless of which cylinder was on its compression stroke, with the other spark plug firing on its cylinder's exhaust stroke, effectively "wasting a spark". The exhaust note is basically a throaty growling sound with some popping. The 45° design of the engine thus creates a plug firing sequencing as such: The first cylinder fires, the second (rear) cylinder fires 315° later, then there is a 405° gap until the first cylinder fires again, giving the engine its unique sound.
Harley-Davidson has used various ignition systems throughout its history – be it the early points and condenser system, (Big Twin up to 1978 and Sportsters up to 1978), magneto ignition system used on some 1958 to 1969 Sportsters, early electronic with centrifugal mechanical advance weights, (all models 1978 and a half to 1979), or the late electronic with transistorized ignition control module, more familiarly known as the black box or the brain, (all models 1980 to present).
Starting in 1995, the company introduced Electronic Fuel Injection (EFI) as an option for the 30th anniversary edition Electra Glide. EFI became standard on all Harley-Davidson motorcycles, including Sportsters, upon the introduction of the 2007 product line.
In 1991, Harley-Davidson began to participate in the Sound Quality Working Group, founded by Orfield Labs, Bruel and Kjaer, TEAC, Yamaha, Sennheiser, SMS and Cortex. This was the nation's first group to share research on psychological acoustics. Later that year, Harley-Davidson participated in a series of sound quality studies at Orfield Labs, based on recordings taken at the Talladega Superspeedway, with the objective to lower the sound level for EU standards while analytically capturing the "Harley Sound". This research resulted in the bikes that were introduced in compliance with EU standards for 1998.
On February 1, 1994, the company filed a sound trademark application for the distinctive sound of the Harley-Davidson motorcycle engine: "The mark consists of the exhaust sound of applicant's motorcycles, produced by V-twin, common crankpin motorcycle engines when the goods are in use". Nine of Harley-Davidson's competitors filed comments opposing the application, arguing that cruiser-style motorcycles of various brands use a single-crankpin V-twin engine which produce a similar sound. These objections were followed by litigation. In June 2000, the company dropped efforts to federally register its trademark.
BIG V-TWINS
F-head, also known as JD, pocket valve and IOE (intake over exhaust), 1914–1929 (1,000 cm³), and 1922–1929 (1,200 cm³)
Flathead, 1930–1949 (1,200 cm³) and 1935–1941 (1,300 cm³).
Knucklehead, 1936–1947 61 cubic inch (1,000 cm³), and 1941–1947 74 cubic inch (1,200 cm³)
Panhead, 1948–1952 61 cubic inch (1,000 cm³), and 1948–1965, 74 cubic inch (1,200 cm³)
Shovelhead, 1966–1984, 74 cubic inch (1,200 cm³) and 80 cubic inch (1,338 cm³) since late 1978
Evolution (a.k.a. "Evo" and "Blockhead"), 1984–1999, 80 cubic inch (1,340 cm³)
Twin Cam (a.k.a. "Fathead" as named by American Iron Magazine) 1999–present, in the following versions:
Twin Cam 88, 1999–2006, 88 cubic inch (1,450 cm³)
Twin Cam 88B, counterbalanced version of the Twin Cam 88, 2000–2006, 88 cubic inch (1,450 cm³)
Twin Cam 95, since 2000, 95 cubic inch (1,550 cm³) (engines for early C.V.O. models)
Twin Cam 96, since 2007. As of 2012, only the Street Bob and Super Glide Custom Models still use the 96.96 cubic inch (1,584 cm³)
Twin Cam 103, 2003–2006, 2009, 103 cubic inch (1,690 cm³) (engines for C.V.O. models), Standard on 2011 Touring models: Ultra Limited, Road King Classic and Road Glide Ultra and optional on the Road Glide Custom and Street Glide. Standard on most 2012 models excluding Sportsters and 2 Dynas (Street Bob and Super Glide Custom). Standard on all 2014 dyna models.
Twin Cam 110, since 2007, 110 cubic inch (1,800 cm³) (engines for C.V.O. models, 2016 Soft Tail Slim S; FatBoy S, Low Rider S, and Pro-Street Breakout)
Milwaukee-Eight
Twin-cooled 107 ci (1,750 cm³): Standard on touring and trike model year 2017+.
Twin-cooled 114 ci (1,870 cm³): Optional on touring and trike model year 2017+, standard on CVO models.
REVOLUTION ENGINE
The Revolution engine is based on the VR-1000 Superbike race program, co-developed by Harley-Davidson's Powertrain Engineering team and Porsche Engineering in Stuttgart, Germany. It is a liquid cooled, dual overhead cam, internally counterbalanced 60 degree V-twin engine with a displacement of 69 cubic inch (1,130 cm³), producing 115 hp (86 kW) at 8,250 rpm at the crank, with a redline of 9,000 rpm. It was introduced for the new V-Rod line in 2001 for the 2002 model year, starting with the single VRSCA (V-Twin Racing Street Custom) model. The Revolution marks Harley's first collaboration with Porsche since the V4 Nova project, which, like the V-Rod, was a radical departure from Harley's traditional lineup until it was cancelled by AMF in 1981 in favor of the Evolution engine.
A 1,250 cc Screamin' Eagle version of the Revolution engine was made available for 2005 and 2006, and was present thereafter in a single production model from 2005 to 2007. In 2008, the 1,250 cc Revolution Engine became standard for the entire VRSC line. Harley-Davidson claims 123 hp (92 kW) at the crank for the 2008 VRSCAW model. The VRXSE Destroyer is equipped with a stroker (75 mm crank) Screamin' Eagle 1,300 cm³ Revolution Engine, producing more than 165 hp (123 kW).
750 cc and 500 cc versions of the Revolution engine are used in Harley-Davidson's Street line of light cruisers. These motors, named the Revolution X, use a single overhead cam, screw and locknut valve adjustment, a single internal counterbalancer, and vertically split crankcases; all of these changes making it different from the original Revolution design.
DÜSSELDORF-TEST
An extreme endurance test of the Revolution engine was performed in a dynometer installation, simulating the German Autobahn (highways without general speed limit) between the Porsche research and development center in Weissach, near Stuttgart to Düsseldorf. Uncounted samples of engines crashed, until an engine successfully passed the 500 hour nonstop run. This was the benchmark for the engineers to approve the start of production for the Revolution engine, which was documented in the Discovery channel special Harley-Davidson: Birth of the V-Rod, October 14, 2001.
SINGLE-CYLINER ENGINES
IOE singlesThe first Harley-Davidson motorcycles were powered by single-cylinder IOE engines with the inlet valve operated by engine vacuum. Singles of this type continued to be made until 1913, when a pushrod and rocker system was used to operate the overhead inlet valve on the single, a similar system having been used on their V-twins since 1911. Single-cylinder motorcycle engines were discontinued in 1918.Flathead and OHV singlesSingle-cylinder engines were reintroduced in 1925 as 1926 models. These singles were available either as flathead engines or as overhead valve engines until 1930, after which they were only available as flatheads. The flathead single-cylinder motorcycles were designated Model A for engines with magneto systems only and Model B for engines with battery and coil systems, while overhead valve versions were designated Model AA and Model BA respectively, and a magneto-only racing version was designated Model S. This line of single-cylinder motorcycles ended production in 1934.
MODEL FAMILIES
Modern Harley-branded motorcycles fall into one of six model families: Touring, Softail, Dyna, Sportster, Vrod and Street. These model families are distinguished by the frame, engine, suspension, and other characteristics.
TOURING
Touring models use Big-Twin engines and large-diameter telescopic forks. All Touring designations begin with the letters FL, e.g., FLHR (Road King) and FLTR (Road Glide).
The touring family, also known as "dressers" or "baggers", includes Road King, Road Glide, Street Glide and Electra Glide models offered in various trims. The Road Kings have a "retro cruiser" appearance and are equipped with a large clear windshield. Road Kings are reminiscent of big-twin models from the 1940s and 1950s. Electra Glides can be identified by their full front fairings. Most Electra Glides sport a fork-mounted fairing referred to as the "Batwing" due to its unmistakable shape. The Road Glide and Road Glide Ultra Classic have a frame-mounted fairing, referred to as the "Sharknose". The Sharknose includes a unique, dual front headlight.
Touring models are distinguishable by their large saddlebags, rear coil-over air suspension and are the only models to offer full fairings with radios and CBs. All touring models use the same frame, first introduced with a Shovelhead motor in 1980, and carried forward with only modest upgrades until 2009, when it was extensively redesigned. The frame is distinguished by the location of the steering head in front of the forks and was the first H-D frame to rubber mount the drivetrain to isolate the rider from the vibration of the big V-twin.
The frame was modified for the 1994 model year when the oil tank went under the transmission and the battery was moved inboard from under the right saddlebag to under the seat. In 1997, the frame was again modified to allow for a larger battery under the seat and to lower seat height. In 2007, Harley-Davidson introduced the 96 cubic inches (1,570 cubic centimetres) Twin Cam 96 engine, as well the six-speed transmission to give the rider better speeds on the highway.
In 2006, Harley introduced the FLHX Street Glide, a bike designed by Willie G. Davidson to be his personal ride, to its touring line.
In 2008, Harley added anti-lock braking systems and cruise control as a factory installed option on all touring models (standard on CVO and Anniversary models). Also new for 2008 is the 6-US-gallon (23 l; 5.0 imp gal) fuel tank for all touring models. 2008 also brought throttle-by-wire to all touring models.
For the 2009 model year, Harley-Davidson redesigned the entire touring range with several changes, including a new frame, new swingarm, a completely revised engine-mounting system, 17-inch (430 mm) front wheels for all but the FLHRC Road King Classic, and a 2–1–2 exhaust. The changes result in greater load carrying capacity, better handling, a smoother engine, longer range and less exhaust heat transmitted to the rider and passenger. Also released for the 2009 model year is the FLHTCUTG Tri-Glide Ultra Classic, the first three-wheeled Harley since the Servi-Car was discontinued in 1973. The model features a unique frame and a 1,690 cm³ engine exclusive to the trike.
In 2014, Harley-Davidson released a redesign for specific touring bikes and called it "Project Rushmore".[125] Changes include a new 103CI High Output engine, one handed easy open saddlebags and compartments, a new Boom! Box Infotainment system with either 10 cm or 16.5 cm screens featuring touchscreen functionality 16.5 cm models only], Bluetooth (media and phone with approved compatible devices), available GPS and SiriusXM, Text-to-Speech functionality (with approved compatible devices) and USB connectivity with charging. Other features include ABS with Reflex linked brakes, improved styling, Halogen or LED lighting and upgraded passenger comfort.
WIKIPEDIA
I know running shoes are not designed to be pretty, but I thing I just bought to most ugly pair available! Are your shoes even worse? Prove me, I don't believe a thing about it :)
Tutorial on Instructables: www.instructables.com/id/Functional-LEGO-Nutcrackers/
With a simple pull of the lever, these decorative figures can open and close their jaws like authentic nutcrackers!
Both of these models were built in the recent weeks leading up to Christmas. The design was pretty straightforward, but two major issues were making the faces look good, and finally getting the hats right. In fact, the green nutcracker's crown took the longest to figure out, and was finally made with hinge plates.
As mentioned in the tutorial, although these can in fact function as real nutcrackers, they're somewhat rickety and best suited for holiday decorations.
New York's subway system is vast, complex, functional and efficient. It can also be bewildering, fascinating, and scary to some.
Wellness over four square meters
The East German bathroom was nothing short of a functional miracle. Every centimeter had been used, every movement planned and every function rationalized so the greatest amount of technology could be squeezed into the smallest possible space.
Only thus was it possible to ensure that every human hygienic need could be permformed over the smallest possible space and at the lowest cost. This meant that all bathroom fittings were made of plastic and were either sometimes leaky or often blocked: sometimes even at the same time.
____________________________________
In the DDR Museum the exhibition depicts life in the former East Germany in a direct "hands-on" way. For example, a covert listening device ("bug") gives visitors the sense of being "under surveillance". One can also try DDR clothes on in the recreated tower block apartment, change TV channels or use an original typewriter. The exhibition has three themed areas: “Public Life”; “State and Ideology” and “Life in a Tower Block”. Each of them is presented under a critical light: the positives as well as the negatives sides of the DDR are explored in this exhibition. A total of 35 modules illustrate these three themes: Media, literature, music, culture, family, private niche, health, equality, diet, childhood, youth, partnership, fashion, border, Berlin, education, work, consumption, construction, living, free time, vacation, environment, party, Ministry for State Security, economy, state, ideology, army, brother states, wall, opposition, penal system and authority. (Wikipedia)
Berlin, Germany.
Here it is. After 3 failed tries to make functional leg armor, I had to settle with just a model. I don't have part to make it functional and solid at the same time or I don't posses the knowledge to make it with parts I have :D
General look and details are same as the ARM part of the suit. I added trusters to the bottom but I am having trouble making them work :(
Functional Photography Co. - Available to Shoot! Contact me for Schedule, Bookings & Prints. - #canon #bwphotogrhy #bnw_captures #visualsoflife #instabw #bwmasters #ig_bw #excellent_bnw #igblacknwhite #blackandwhite #bnw_demand #bnwmood #bnw_planet #bnw_society #bnw_magazine #bw_pictures #bnw_of_our_world #top_bnw #bw_lovers #bw_crew #noir_vision #bnw_diamond #flair_bw #rsa_bnw #bnw_life #bnw_guru #love_bnw #jj_blackwhite #bwsquare #owl #carved ift.tt/2GVjdQM
The BMW 328 Mille Miglia Roadster was a major design statement, well ahead of its time, using an emotive formal idiom that united aesthetic and functional aspects in an incomparable way. Its outlines reduced aerodynamic drag and wrote a new chapter in design history. The BMW 328 Mille Miglia Roadster is still a unique source of inspiration for BMW Design.
1.971 cc
6 Cylinder
130 PS @ 5.750 rpm
Vmax : 200 km/h
1 ex.
BMW Museum
Am Olympiapark 2
Munchen
Deutschland - Germany
September 2016
Tutorial on Instructables: www.instructables.com/id/Functional-LEGO-Nutcrackers/
With a simple pull of the lever, these decorative figures can open and close their jaws like authentic nutcrackers!
Both of these models were built in the recent weeks leading up to Christmas. The design was pretty straightforward, but two major issues were making the faces look good, and finally getting the hats right. In fact, the green nutcracker's crown took the longest to figure out, and was finally made with hinge plates.
As mentioned in the tutorial, although these can in fact function as real nutcrackers, they're somewhat rickety and best suited for holiday decorations.