View allAll Photos Tagged 2ndamendment
Students from Marjory Stoneman Douglas High School lined bleachers at a March for Our Lives rally held in Parkland, Fla., March 24. Students emphasized the power all adults have to change gun laws if they get out and vote. “Policy change is not as difficult as losing a loved one,” one student said. Photo by Kathy L. Gilbert, UMNS
Warning: camera geek boredom ahead:
Interesting results from a resolution test I performed. I tried three configurations of my orange 1970s Celestron C90 telescope/spotting scope:
The 'scope is a 1000mm focal length, f/11 Maksutov mirror-type model:
1) Nikon D600 mounted to the C90 with a threaded adapter.
2) Nikon D600 mounted to the C90 with a threaded adapter and an inexpensive but excellent condition 2X aftermarket F-mount teleconverter.
3) Nikon D600 mounted to the C90 with a hybrid star diagonal and a 1.25" telescope to camera adapter. I used it in eyepiece projection mode, with a Meade Series 4000 Super Plossl 9.7mm (103X mag.).
In all three cases, the test target was the good old USAF1951 issue. All shots were taken on a tripod, at the same distance. There was some wind, so I had to wait for quieter times to let the rig settle. You'd be surprised how much jiggle there is when looking at the LiveView image, fully zoomed in on a 103X eyepiece image.
Camera ISO had to increase as mag went up, to keep shutter speed fast enough to freeze motion. Even though I was shooting in infrared-remote LiveView mode, thus no mirror slap, shutter slap will jiggle the image, along with the wind. I shot multiple times in each setup, tweaking the VERY sensitive focus of the C90 back and forth through the apparent point of best focus, and hoping for lightest wind. I chose the best of each set of images for the final comparison.
I left the eyepiece projection crop at full res., and upsampled the other two modes to match res. The result is that resolution appears to be identical in all three setups. Hmm. Perhaps the C90's inherent resolution limits are being fully exploited by the D600's 24 megapixel sensor with no further mag. So any further mag. is simply magnifying the limits, and making for a MUCH dimmer image.
I've used the long exposure noise reduction feature on my Nikon D50 on occasion, just assuming it was doing "something". But waiting for the camera to make a dark frame exposure right after every >1 sec. exposure can be tedious.
This feature is doing something called "dark frame subtraction". Even with no light entering the camera, a photosite (pixel) on the image sensor may build up a slight charge, which will create a small increase in the brightness value for that pixel in the final digital image. Unlike quantum noise, the pattern of this unwanted buildup of noise (called dark current) is fairly consistent from frame to frame, as long as conditions are identical (sensor ISO speed, exposure time and ambient temperature). To combat this effect, a second identical exposure is made immediately after the real one, with the shutter closed. The camera subtracts the values in the "dark frame" from the first "light frame", and therefore slightly reduces image noise.
The tests I've done in the past were 30 second exposures of totally dark scenes (lens cap on while in closet). When I compared the NR off and NR on exposures, I could see no apparent difference. They both look totally black. But after doing some more reading about processing digital images from astrophotgraphy, and learning more about Levels and Curves in image processing software, I've figured out how to see the difference of this method of noise reduction. With some judicious linear amplification of values way down low in the histogram, the above results can be had.
The upper portion of this image is a 100% crop of a frame from my Nikon D50. Exposure time was 30 seconds at ISO200. The crop is from the upper left portion of the full frame. As you'll see, besides the overall noise, there is a "bloom" at the upper right. This bloom is also found in some of my more heavily-processed long exposure photos taken without NR. It might be an on-chip amplifier, or some such.
The lower half of the image is the same cropped portion of the full frame, this time shot with in-camera NR turned on. Quite a difference, especially around the bloomed area.
Keep in mind that both of these frames appear totally black when viewed in their unmolested out-of-the-camera state. The very slight noise seen here would only be an issue when an image is heavily manipulated, such as when trying to pick out more detail in the black depths of an astrophoto.
View large for better detail.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This was my first time shooting fire dancers/spinners at night. Some post processing was required to get the results seen here.
I used my Nikon D600 with a Sigma 70-300mm f/4-5.6 "APO" macro lens with internal focus motor ($100 used on eBay).
I have a bunch of other shots of the firedancers in this set- check 'em out if'n ya like this sort of thang.
Wayne LaPierre is CEO and the Executive Vice President of the National Rifle Association.
The source images for this cartoon of Wayne LaPierre are Creative Commons licensed photos from Gage Skidmore's and cm195902's Flickr photostreams, a U.S. Military - Joint Task Force Guantanamo photo, a U.S. Air Force photo and Creative Commons licensed images from plural's flickr photostream and Jeffery Love's flickr photostreams.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This is my Kearney & Trecker horizontal milling machine. It was made during World War II, and was presumably used to produce parts for the war effort.
The "War Finish" mark was placed to indicate to any potential post-war customers that this is not the usual level of cosmetic finishing that Kearney & Trecker would apply to their machines. The government ordered that no extra time be wasted on making a machine tool pretty when there were lives at stake.
This old mill has been sitting in my yard for quite a few years, and is missing some parts, some of which were sold to bring new life to other old K&T mills.
It will soon be scrapped, unless some intrepid parts scroungers save at least some relics from the aging derelict.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This is my among my first experiments in focus stacking.
This is the muzzle and rifled bore of a 1954-vintage Romanian M44 bolt-action carbine, a Mosin-Nagant variant. Caliber is 7.62x54R Russian.
The bore appears to be in fair to good condition, to the naked eye. There is some pitting and general roughness, nothing terrible. Certainly still shootable.
I shot a series of 10 photos with my old Nikon D50 DSLR, and a Tokina F/2.8 100mm macro lens. Each image was shot at F/16. I changed the focus point manually between each exposure, stepping from the crown of the barrel to the most distant point of the front sight base.
I used the trial version of Zerene Stacker to combine the 10 images into this deep-field image.
Here's the website for the software I used:
www.zerenesystems.com/stacker/
The bore was lit by pointing my very bright Luxeon Rebel LED flashlight down the bore from the breech end. External lighting was provided by a cheap TTL ringflash, mounted on the lens.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
I like the layers of color in the Bokeh (out of focus background).
500mm Samyang F/8 preset lens, handheld.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
54th self-portrait for 365 days.
SOOC
The always popular 2nd amendment. My boyfriend has the right to keep and bear arms and I have the right to pretend to be Miss America for an evening.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
4/5/2014 Mike Orazzi | Staff
Participants listen to Connecticut Citizens Defense League President Scott Wilson during a CCDL gun rights rally at the Connecticut state capitol in Hartford, Saturday April 5, 2014, speaks out against the state's gun control law passed one year ago on April 4, 2013 restricting magazines to 10 rounds and prohibiting the sale of certain semi-automatic firearms, including the AR-15.
Video & Slideshow here: youtu.be/XbILfKZkMbs
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This is a wall of our bathroom. It had been covered by drywall since 1953, when the house was built. It is going to be left bare, now that it has been treated with three coats of water-resistant semi-gloss polyurethane.
These are wall panels made from scrap 2x4 pieces, glued up into (mostly) 24" wide panels, grooved all around for splines, and full height (about eight feet).
After the glue-up, each panel was run through a planer to true up both faces, leaving the finished thickness at about 3-1/4".
Every wall in the house, interior and exterior, is comprised of these panels. We also own two more houses in the same "compound" in Reno, Nevada. They were built in 1958, and are also entirely built of these same panels, though only 12" wide each.
We have never been able to find any information online about this method of construction. I assume that they were built by a company in Reno that had access to large quantities of scrap 2x4 cut-offs.
Zoe is now Sun brewing our go-juice in handy-dandy portable doses. Seven parts water, two parts tea, one part Meth (just kidding).
Samyang / Rokinon 8mm f/3.5 fisheye lens.
The lens hood has been “shaved” to allow a nearly full circle image to be captured.
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes: