View allAll Photos Tagged pwm

Spitzbergen

 

Munich Marstallplatz

"Pavillon 21"

mini opera space

Oldtimertreffen in München beim Frühlingsfest

 

PRINT WEAVE MAKE brochure (designed by Luke Lucas - www.lukelucas.com/). Open days in November at Australian Tapestry Workshop, Australian Print Workshop and Craft. Come along!

Had to drill a small hole between the output sockets for a miniature knob... above the Pulse waveform output.

PWM Wealth Tech Awards, 8 June 2023, London

The trolley being loaded at Exmouth Junction on 5th February, 1998.

... on Veroboard. Here it is installed in the bottom of the cabinet.

MCHRTF04C0 - FAN SPEED CONTROLLER-CUT PHASE PWM 4A/230VAC FASTON

 

The MCHRTF series electronic devices are single-phase voltage controllers that use the principle

of phase control to adjust the effective voltage output to the load, based on the phase of the

PWM control signal

One typical application is the speed control of single-phase condenser fan motors, based on

the pressure or the temperature measured on the heat exchanger.

The MCHRTF controllers are protected against short circuit with a fuse located on the outside

of the board, thus allowing easy inspection and replacement, where necessary (refer to Table 3

for the correct replacement of the fuse). Always check with the manufacturers that the motors

used are suitable for operation with phase control devices.

Oldtimertreffen in München beim Frühlingsfest

 

ON Semiconductor has expanded its portfolio of ac-dc power solutions for home electronics with the introduction of the <a href="http://www.onsemi.com/PowerSolutions/parametrics.do?id=976"NCP1234 and NCP1236 family of fixed frequency pulse width modulation (PWM) current mode controllers. These solutions are targeted at ac-dc adapter applications for laptop/notebook computers, LCD displays, printers and household consumer electronics.

 

Read the press release.

Gracias a todos por vuestros comentarios y reconocimientos...

 

Por favor, no use esta imagen en los sitios web, blogs u otros medios de comunicación sin mi permiso explícito - Todos los derechos reservados ©.

 

Please don't use this image on websites, blogs or other media without my explicit permission - All Rights Reserved ©.

Gracias a todos por vuestros comentarios y reconocimientos...

 

Por favor, no use esta imagen en los sitios web, blogs u otros medios de comunicación sin mi permiso explícito - Todos los derechos reservados ©.

 

Please don't use this image on websites, blogs or other media without my explicit permission - All Rights Reserved ©.

Pulse width modulation

Photo Credit: Jim Messina of Prairie Wings Media

Blanket ends from Pendleton Woolen Mill. These are just ends from the huge bolts that get cut up into finished blankets for sale. I figured these ends were about the right width & length to use as scarves. This was waste, originally headed to the landfill, before the mill folks realized crafters would pay to turn it into patchwork blankets, details on clothing, and more.

ParksAndRec - Photo Credit: Jim Messina of Prairie Wings Media

Taken during 20th PWM Munich Photowalk.

Gracias a todos por vuestros comentarios y reconocimientos...

 

Por favor, no use esta imagen en los sitios web, blogs u otros medios de comunicación sin mi permiso explícito - Todos los derechos reservados ©.

 

Please don't use this image on websites, blogs or other media without my explicit permission - All Rights Reserved ©.

The PWM speed pot is also the on/off switch - push/pull variety...:)

Portland participated in Making Strides for the first time this year, raising $400 for the American Cancer Society with a team of eight walkers. The team braved a cold and rainy day for the event.

 

PWM Airports Crewmember Nicole said, "It was an inspirational day with all of the survivors and supporters — we can't wait for the next to come around." In total, 3,000 participants attended the walk, raising $250,000.

The fan spinning over the PWM hubs on the main electrical board. One of these was giving us a lot of trouble with Mjolnir (the hammer), turns out it was just a faulty PWM cable.

 

- Karthik Urs

1 2 ••• 25 26 28 30 31 ••• 79 80