View allAll Photos Tagged brackets
Old pole top insulator pin brackets, double here for a small angle, with brown pin insulators from that era.
9shooter camera bracket for connecting DSLR stills camera and hd video camera, for shooting stills and video at the same time.
I'm not sticking my neck out. Probably on beech. It was too difficult to get close to this, so I was unable to look properly.
9shooter camera bracket for connecting DSLR stills camera and hd video camera, for shooting stills and video at the same time.
LONDON, ENGLAND - MAY 10: Fans in the audience at the League of Legends - Mid-Season Invitational Bracket Stage on May 10 2023 in London, England. (Photo by Colin Young-Wolff/Riot Games)
Bracket fungi, or shelf fungi, among many groups of the fungi in the phylum Basidiomycota. Characteristically, they produce shelf- or bracket-shaped fruiting bodies called conks that lie in a close planar grouping of separate or interconnected horizontal rows. Brackets can range from only a single row of a few caps, to dozens of rows of caps that can weigh several hundred pounds. They are mainly found on trees (living and dead) and coarse woody debris, and may resemble mushrooms. Some form annual fruiting bodies while others are perennial and grow larger year after year. Bracket fungi are typically tough and sturdy and produce their spores, called basidiospores, within the pores that typically make up the undersurface.
8bar-bikes.com/products/super-tretlager-bottom-bracket
Specification:
cartridge bearings
square type
BSA / 68mm (English)
double sealed bearings mechanism
thread: BC 1.37“ x 24T.
cr-mo hollow axle
weight: 250g
A disused lamp bracket, made from a length of old rail and now used for growing ivy. Reedham station, Norfolk, 8th April 2016.
Lunchtime wander in the woods - and found some fungi. The sun even shone briefly.
These brackets were smooth white underneath, and a neighbouring fallen branch had masses of them.
France
1950s
This high quality bottom bracket was paired with the model # 54 steel cottered crank set.
Another bracketed shot from this mornings trip to the lighthouse. Processed with a bleach bypass in Niksoft HDR Efex Pro.
Switzerland
1980
The brainchild of Assos founder, Toni Maier Moussa, this cup-and-cone type bottom bracket came with Assos crank sets. Designed to allow for side-to-side chain-line adjustment, the cups, lock rings and dust shield are all made of lightweight alloy. Even the crank bolts were through-drilled to save weight.
Hasselblad interpretation of this shot. Kind of happy about this one, I remember the shutter speed was quite slow and I was worried about camera shake. No shake reduction in Hassies :-D
Hasselblad 501c + Carl Zeiss Distagon 50mm f4 + Fuji Velvia 50
www.cadillacforums.com/threads/puttin-on-the-ritz-1984-el...
This installment begins back, way way back,back into time. In the days we could have large gatherings, touch our faces, eat inside restaurants, and lived perilously close to the edge of running out of toilet paper. Picture it, Thanksgiving weekend, 2019…Oh wait, back a bit further…August, 1983.
Some dunderhead salesman in southern California takes an order from a buyer with great taste, a beautifully optioned 1984 Eldorado Biarritz in the ultimate color combination of Black/Black/Red. Said dunderhead gets everything right on the order-except for one tiny detail. The desire for a CF5 Astroroof is lost in translation from the prospective buyer and never makes it into the POS.
Car arrives in September. No sunroof. What gives? Our apologies sir, we’ll get that taken care of right away. Car is driven to an ASC installer. Another dunderhead gets out a jigsaw and cuts a hole thru the roof. A 38” (the biggest you can fit in an Eldorado with roof-mounted seatbelts) ASC sunroof is installed. Car is returned to dealership, buyer eagerly accepts delivery, none the wiser about factory vs aftermarket sunroofs.
For those who don’t know, when you order a car with a sunroof, the car is born with a hole in the roof. Mounts are cast into the roof panel, and the sunroof assembly seats in them and the glass panel has a channel for a nice rubber gasket that seals everything up nice. Then a vacuum formed headliner backing board is cast to perfectly hide everything. When you get an aftermarket sunroof, someone gets a stencil and a jigsaw, and cuts your roof panel and headliner open, pops a trim ring in the hole, and hangs a sunroof pan on the trim ring. If you’re lucky they will drill additional reinforcements to marry the pan to the roof structure. Then they get a bunch of headliner material, pull it taught from the corners of the car to the opening in the roof, and send you on down the road.
Anyway, back to Thanksgiving 2019, and the jigsaw dunderhead’s work starts to come undone.
When I had purchased this car, it needed headliner help. The material was loose, but not sagging appreciably. Additionally, someone had tried to superglue the material all around the perimeter. The material was kind of floating in place, which I thought was weird. I ended up getting some super strong neodymium magnets to hold it taught-which worked ok until it was humid out, or driving on the highway with the windows down as the liner would look something like a sailboat in the wind.
My fix was simple-find a factory sunroof equipped car and get the headliner board out of it and pop it into my car. Found out that that was easier said than done, and after a lot of junkyard expedition, kept coming up empty handed. Finally after years, I came into someone parting a factory sunroof Eldo on ebay and after a lot of trouble was able to get it shipped to me
The board needed some help, and after getting all the old foam off of it and some repairs made to restore the structure (the sunroof headliner board is really thin and flimsy, even compared to the stock non-sunroof board) I tore the interior apart to facilitate getting it in and out as I knew I would have to make “some” tweaks to reconcile the aftermarket hole location to the factory one. The sunroof assembly would also need to come out to recover the sunshade; as well as reseal the panel.
We can see here how the trim ring supports the pan assembly from the center. I have to say though, this was about as clean an install as an aftermarket sunroof can come with lots of extra bracing and no factory roof reinforcements cut. We can also see a very chintzy felt seal stuck to the trim ring
Got the sunshade recovered quickly. I later removed the black plastic covered jute that was glued to the pan-factory did not have this and it would have made the board sit too low when installed in the car. The gray rubbery stuff at the front of the pan was also stripped off for the same reason. I also swapped to the factory grab handle that was included with the board.
Also recovered the sail panels. I chose to leave the foam backing on these as it is not the usual headliner stuff that turns to jelly, its more like a sponge material and seemed to be holding up just fine.
I also added PED connectors to the sail panel interior lights that the factory curiously left out. Not sure how they installed these as the harness is one giant piece, but it means that you can’t take the sail panels out without having the lights dangling in the back. This will become important later.
I then devised a new seal. I threw away all the felt and used some 3M Adhesive remover to get rid of the stuff they had glued it with. Nasty stuff but did a good job. The new seal was the first part of this that took a LONG time. Aftermarket roofs from this time use some kind of felt tape to cut down on wind noise and slow water ingress into the pan, and while still available, there is way better out there today. (In spite of how it looked on my car though, it never leaked?!?! Wind noise was an issue with the shade open though) I decided on a rubber seal, and after getting a whole bunch of samples, the stuff I had initially ended up trying was pretty thin, but rigid strip of rubber. After gluing it on with 3M yellow weatherstrip adhesive (which does NOT work as good as the adhesive remover), I put the pan back in the car to see how it would work.
No photos of the failure here, but no good. The material was too rigid and too grippy, and would cause the roof to bind midway thru its travel. Then it tore off in the corners. Ugh! Pan back out, strip off the remaining seal and glue and go back to the drawing board. I ended up buying this
www.austinhardware.com/rubber-seal-single-500-rolls.htm
Which is a hollow piece of rubber that lets the panel travel without binding, and still squishes into a really tight seal. Looks like its out of stock now, but something with close to those measurements in a D-shape is a possibility for someone looking to reseal their ASC aftermarket sunroof. It was another 3M product, that was just a peel and stick affair-way easier than the yellow goopy adhesive route. Seems like a really strong bond, and seals fantastically against wind and water. 0 wind noise now, and no leaks in a downpour when parked, or cruising at highway speeds. Roof moves without binding now
I also decided to put the new seal onto the glass panel itself as it seems like that’s the easier life for it-if I put it around the opening, the pop rivets from the panel would abrade it. Super happy with this.
Next task was of course the headliner. With the pan now back in the car, I could take measurements and properly scribe/cut/fill the board as needed. Again, easier said than done. This was a weeks long ordeal between cutting the board, fiberglassing new material in, more cutting, more filling, coronavirus insanity, etc. Long story short, my roof was installed a few inches more aft than a factory roof would have been, which meant a lot of tweaking to get the kick-up over the rear passengers head in the right spot. Additionally, I needed to build out the map light drop down to accommodate the motor.
Here is the mess I ended up with
I also affixed strips of 3M dual-lock (it is like a heavy duty version of the stuff that holds in an Ezpass) to the back of the board and the pan to hold it tightly-the factory had attempted this with a similar product in the non-sunroof car headliner board. I was super skeptical that my fudgery would cover well at all, but I have to say that foam backed headliner material must be some of the most forgiving stuff around. This took me months to complete, working off and on from November thru April. Ultimately though, I’m happy with it.
While the interior was out, there was another thing I wanted to do. About a year ago, I was following a buddy as he took his Eldorado to drop off at a shop-couldn’t help but notice how small the brake lights (and the rest of the car) seemed compared to all the bulbous modern cars surrounding it. Then I had a couple of SUV’s roll up way too close for comfort on the back of the car-one was close enough that I launched the Eldorado up and to the side to avoid getting hit. Knowing that getting rear ended by a careless driver would probably result in my untimely incarceration, I set out to do something about rear visibility.
The federal government mandated 3rd brake lights for passenger cars for model year 1986. Cadillac was slightly ahead of the curve with this with the 1985 Deville/Fleetwoods which got these in the fall of ’84. Apparently the science is behind them and they do result in fewer rear end collisions. So I decided to add one of them to the Eldo.
There were a few different versions of these things made, with short, medium and long necks to mate with the rear window-one for a Fleetwood Brougham has the tall one, and one for an 80s Buick Riviera like the one seen above is short. The short one is the best size for the Eldo, any taller and it would look pretty bad. Then the gasket that seals it to the window is different for each different model. Fortunately a potato peeler does a great job of cutting things down to size to match the Eldos vertical rear window, and the material can be easily sanded to get out any little imperfections to make it seal nicely and not leak light. An ideal donor for one would be one an 86-91 Eldo or Seville without a factory vinyl or carriage roof.
A quick mockup
All of these lights mount the same way, with this little bracket cutting into the package shelf and screwing in to the metal underneath. This is not possible on the Eldo as the package shelf reinforcement under the center won’t let this happen. So I had to modify the bracket to sit flush on the package shelf, and add two holes to the shelf to get the screws through. They screw right into the package shelf reinforcement.
The next step was wiring. It is not as simple as tapping a brake light wire and running across the package shelf to the light. Since the Eldos tail lights do everything- brake, signal and hazard, just tapping a wire would cause the center light to flash with the signals or hazard. GM rectified this by using a different brake switch to prevent backfeeding. See the original gray switch, with an in and out, and the new beige one, with a supply, and two isolated outputs. This puts the 3rd brake light (acronym: CHMSL “Center High Mount Stoplight) on its own branch-but also means that you have to home run a wire all the way to it. The wire chase made quick work of this however. I had a pretty long link of 3rd brake light harness, but not quite enough to make it to the front of the car. I put another PED connector of the same kind that I used on the sail panels to join this blue wire I ran from the switch underneath the drivers side rear seat arm rest, which is accessible by removing the ash tray if need be. The stock package shelf reinforcement actually ended up being drilled for the wiring, so I’m not sure if this was something that was in the works for the Eldo.
The version of the brake switch I used allowed me to keep the cruise control connector, and only change the brake light connector itself (part 12117354). I wanted to keep this as non-invasive as possible as I hate being upside down under the dash (though I see to find myself in that position a lot…) I will search around for the part number for the brake light switch itself.
The last trick I wanted to pull before I put the interior back together was to replace the horrible rearview mirror. I forgot how bad these things were (or more like, no one ever noticed before there were LED headlights on other people’s cars that are tall enough to be flush with your back window) but it seems like the mirror was good for one thing; blindness. They have two settings-blindingly bright where others headlights fry your retinas at night, or completely blind, where you can’t see a thing behind you.
My daily driver has a great auto dimming mirror that still lets you see everything without blinding you, made by Gentex. About the same size as the Eldo rearview. I was casually browsing their offerings to see what kind of money we were talking, when I noticed they offered an upgraded unit as compared to the one installed on my car-one with an LED compass feature that was *drumroll* amber colored! Just like the center stack on the Eldorado! So needless to say, the project was underway quickly.
Wired it in cleanly to an existing ignition power on the fuse box
I had to buy a new button to mount it, stock Eldo one was too small to hold it. Check out the dashboard illustration on the glue I bought to stick it on with!
And here it is mounted up!
I am super happy with the mirror. It works great and is a really close match to the amber on the center stack. They even have the same segment check timing when you turn the ignition on Unfortunately it does not dim with the rest of the dash panel, so that’s a letdown, but if desired you can turn the compass off if you wanted to dim everything all the way as I like to do when I’m out of the city on a dark road.
Now, you may notice that the visors are all kinds of messed up. Progress has a price I guess. My long-fought for 1988 Deville visors are NG with the new headliner board-they’re just too big and interfere with the bump out for the map light. I wish I would have known as I could have easily shrunk this bump out when I was doing surgery on the board but its too late now. I’m at a crossroads of reinstalling my old red Eldo visors with known good arms swapped into them (which are probably super faded next to the new material but are impossible to reupholster right) or finding another late 80s more robust GM visor and reupholstering/swapping them in.
I still have more stuff to add to this which may come tomorrow as my fingers are about to fall off!
Not something I thought I would see at South Ottawa. Ohio Central 4028, leased to I&O from G&W, has a good hand on a 53 car Sunday extra from NorthStar in Delta, headed for Ford Park Yard in Lima.
TOKYO, JAPAN - JUNE 18: Victor "Victor" Wong of NRG reacts with excitement after victory against DRX at VALORANT Masters Tokyo Brackets Stage at Tipstar Dome Chiba on June 18, 2023 in Tokyo, Japan. (Photo by Colin Young-Wolff/Riot Games)
Here's the bracket out of the carIt's laying on a piece of 8.5x11 paper. I replaced this with two 10mm x 1.5 cm bolts with locknuts.
LONDON, ENGLAND - MAY 09: Jeong "Chovy" Ji-hoon of Gen.G Esports prepares to compete at the League of Legends - Mid-Season Invitational Bracket Stage on May 9 2023 in London, England. (Photo by Colin Young-Wolff/Riot Games)
The last few years have seen some fantastic improvements to road and mountain bike technology and along with this comes a new phenomenon called BBC - bottom bracket confusion. To try help our clients out I thought it wise to publish this spec list. If you need help beyond what you see here please e-mail me at clive@glorycycles.com
See the spec chart on our blog: glorycycles.blogspot.com/2011/08/bottom-bracket-size-para...