View allAll Photos Tagged Injection
22nd April 2009
22/30 - 'A Month of Medicine'
This one didn't turn out how I had pictured... I might try this one again.
Migraine headaches are one of the common types of headache that affect one in seven people in the world. That makes it the third most common disorder in the world. In America alone, nearly 12% of the population consists of men, women, and even children suffer some migraine headaches. For more details, visit www.progressiveneurosleep.com/procedures/botox-injections/
CEA Project Logistics Thailand was contracted for the demobilisation and export to Malaysia of a High-Pressure Plastic Injection Moulding Machine weighing over 150 Tonnes.
Working alongside Mitsubishi technicians for this demobilisation project (the original machine supplier) CEA initially disconnected all the hydraulic interfaces between the machine and fixed supply, in addition, all high and low voltage electrical connections were disconnected.
After disassembling all interlocked gates and fencing, the hydraulic power packs were removed and packed into temporary supports. The access platforms and plastic supply hopper was removed next. A Sepro robotic arm assistor used for the omnium unloading required some expert rigging to ensure it was fully balanced before being dismantled. The injector unit was removed and loaded directly onto a low bed trailer for immediate load-out out to the CEA facility for packing.
The heavier components, 46 tonne die head and the rear platen with ejector unit at 42 tonnes were the final components to be dismantled. The tie-rod cap plates were removed first and then by use of the mobiles cranes the teams proceeded to slide out the four 6 Tonne tie-rods that connect the die head and platen, each of these were immediately loaded onto wooden supports and treated for rust protection.
Using special jig and tools specifically produced for this demobilisation, the CEA special projects team lifted both the die head and then the platen by means of top and tailing cranes. Both the die head and platen were moved into a horizontal position and loaded directly onto low bed trailers. They were then transported to the CEA facility for packing onto MAFI trailers in preparation for break-bulk load out. Other auxiliary parts and equipment were packed, stuffed and secured in several 40’ containers ready for shipping.
The doctor is administering an injection to my wife but it looks more like a drill! The nurse is shying away.
this is what 2 weeks of iv injections will make your hands look like. They look better in the photo than they did in actuality.
1974 Citroen DS23 Fuel Injection with optional Factory Air-condition. Seen at Citroen Conservatoire in Aulnay Sous Bois France
Alfa Spider 2.0 'Nuovo' - Series 4 (1990-1993)
first registration: 1991
power: 88 kW (120 PS)
cubic capacity: 1962 cc
Zylinder: 4 in-line
The Alfa Romeo Spider (105/115 series) is a roadster produced in four series (‘Duetto’, ‘Fastback’, ‘Aerodinamica’ and ‘Nuovo’ over 120’000 units in total) from 1966 to 1993.
Widely regarded as a design classic, it remained in production for almost three decades with only minor aesthetic and mechanical changes.
The three first series were assembled by Pininfarina in Grugliasco and the fourth series in San Giorgio Canavese.
The last Spider was produced in April 1993, it was also the last rear wheel drive Alfa Romeo produced before Alfa Romeo 8C Competizione was introduced.
The final major change to the Spider as Series 4 (“Nuovo”) came in 1990. The primary mechanical change was that the Spider was given Bosch Motronic electronic fuel injection with an electric fan. Externally, the Spider lost its front under-bumper spoiler and the rear trunk-lid spoiler and picked up 164-style rear lights stretching across the width of the car as well as plastic bumpers the same color as the car.
In North America, the styling changes did not appear until the 1991 model year; 1990 models featured the Motronic fuel injection but retained the black bumpers.
Power steering, larger knee bolsters and a driver-side airbag also appeared as standard for North American market Spiders.
Production of the original Spider ended in 1993.
ISO, QS and UL cert. plastic injection molder. Plastic Bobbins, insert / overmolding, custom parts. High & Low Volume Plastic Injection Molding. Plasti-Coil, Inc. is located in Lake Geneva, Wisconsin www.plasticoil.com/
Afterwards, they realized that he should have been on her other side, so as not to cross over himself to get to the sharps container.
Vital Signs Training Workshop @ Stanford
Insert molding process is kind of a special injection molding style in the traditional molding process. Now are wildly used in the injection industry. In our daily life that we can see many plastic products are produced together with the metal parts. The traditional way to achieve this, people first make the plastic parts, the metal parts that will be combined with the plastic parts by Laser, hot melting etc. This is a kind of tedious process and required huge manual works. With insert molding occurs, we no-longer worried about this process. Normally the metal parts will be put together into a mold on the injection machine. The metal parts will be hold inside the mold by some special structure or fixture and then will be molded together with plastic.
Insert injection molding process is wildly used in many industries. Feman tooling is an expert making the insert molding. With years of injection experience we successfully making the products for many customers and is highly appreciated.
API’s injection molded cases are single wall containers that provide a smaller profile and lighter weight while still maintaining a quality protective packaging solution. Each case is watertight and airtight, and (depending on size) is available with extensions, handles and wheels.