View allAll Photos Tagged 3dprinter
This screen video shows how the #3DBenchy 3D print calibration STL file is sliced for SLA 3D printers in the web-based SLAcer slicing software. - http://ift.tt/22OQnXV - http://ift.tt/1nL0NFz - http://3DBenchy.com #3Dprinting #3Dprinter #slicer #slicing #3Dprinter #SLA See video: ift.tt/22OQoed Learn more about 3D printing at 3DBenchy.com
SVENSKA:
Den personliga fabbster 3D-skrivare från Sintermask.
Läs mer på: fabbster.creativetools.se
ENGLISH:
The personal 3D printer fabbster from Sintermask
rollstroll.com/2017/04/13/redtube-and-youjizz-featured-wo... - #3DPrinter, #NewTech, #Offbeat, #Porn, #Pornhub, #Redtube, #Technology, #Vagina, #Youjizz, #YouPorn
The extruder carriage rides on the X rods with two 45mm long LM8LUU linear bearings. LM8LUU bearings have 8mm ID, 15mm OD, and 45mm length. The cutouts in the carriage for the bearings is approximately 0.5 inches wide. This allows the carriage to ride approximately 1 mm above the top of the X rods.
Z platform is from FlashForge.
Printed parts on Y axis are TR_Y.stl from www.thingiverse.com/thing:252041
Printed parts for Z axis are Z_stage_lower_100.stl and Z_stage_upper_100.stl from www.thingiverse.com/thing:362779
The 8mm Y rods run parallel to the left and right sides while the 8mm X rods run parallel to the front and back sides. The Y rods are mounted to the frame with flanged shaft support blocks. The X rods are supported by the Y rods.
Y rods: 8mm diameter, 300mm long.
X rods: 8mm diameter, 340mm long.
Z platform is from FlashForge.
Printed parts on Y axis are TR_Y.stl from www.thingiverse.com/thing:252041
Printed parts for Z axis are Z_stage_lower_100.stl and Z_stage_upper_100.stl from www.thingiverse.com/thing:362779
Z platform is from FlashForge.
Printed parts on Y axis are TR_Y.stl from www.thingiverse.com/thing:252041
Printed parts for Z axis are Z_stage_lower_100.stl and Z_stage_upper_100.stl from www.thingiverse.com/thing:362779
SVENSKA:
Den personliga fabbster 3D-skrivare från Sintermask.
Läs mer på: fabbster.creativetools.se
ENGLISH:
The personal 3D printer fabbster from Sintermask
Two things not in the photo: our 100 page printed manual, and the USB stick that comes with pre-configured firmware, settings for slic3r, and sample STL files. www.botbuilder.net
21 ‪#‎3DBenchy‬ boats on a single 32-hour ‪#‎3dprint‬.
Read more at: 3dbenchy.com/?p=677
‪‬
X and Y stepper motors are Kysan 1124090. Available from Ultimachine. Like the Z stepper motor, these motors require more current than the standard Makerbot X and Y stepper motors. You will need to use modified stepper drivers.
Motor and idler brackets from www.thingiverse.com/thing:364426 .
Note removal of the upper corner brackets to make room for the idler brackets. Upper corner brackets may be retained if using the idler bracket from www.thingiverse.com/thing:252041
Motor and idler brackets from www.thingiverse.com/thing:364426 .
Note removal of the upper corner brackets to make room for the idler brackets. Upper corner brackets may be retained if using the idler bracket from www.thingiverse.com/thing:252041
Thermistor circuit with CD-ROM audio connector wiring (MPC-2 connector).
For $5.60 US you can order three of these boards from OSH Park. That includes free shipping within the USA. Note that OSH Park always sells in units of three. The URL is
oshpark.com/shared_projects/HTTIQlfd
The sole required component (beyond the 100K NTC thermistor itself) is one 4.7K resistor which you can likely buy at a Radio Shack (Digikey S4.7KCACT-ND). The optional components are a 0.1 uF capacitor (Digikey 339-4151-ND), a MPC-2 connector (CD-ROM audio; Molex 0705550038; Digikey WM4177-ND), and a two position screw down terminal (Phoenix 1729128; Digikey 277-1247-ND).
Motor and idler brackets from www.thingiverse.com/thing:364426 .
Note removal of the upper corner brackets to make room for the idler brackets. Upper corner brackets may be retained if using the idler bracket from www.thingiverse.com/thing:252041
Photo used by pepen28k.weebly.com/extras.html.
Photo used by www.ryanlionlibrary.com/makerspace.html.