This was my first attempt at printing the 3D cube test file.

Ended the print early when I realised nothing was on the build plate. It stuck to the bottom of the vat holding the resin rather than the build plate so I ended up with a snowflake effect where each layer was printed in an overlay fashion rather than a layered build-up fashion as it should have been.

3D-printed on a Objet Connex 350

mady by Institute of Polymer Product Engineering at Johannes Kepler University Linz / Austria (2010)

3Dprinting, 3D printing, 3D-printing

thefwoosh.com/2014/05/action-figure-feature-shapeways-3d-...

3Dify body scanner in action at Broadcasting House for BBC World Service 3D printing special; Photo credit: Kati Byrne

Printed on a Printrbot simple maker (wooden)

For more information see fffff.at/liberator-variations/

For 3d models see www.thingiverse.com/thing:142879

#3dprinting

www.thingiverse.com/thing:2779274

www.youmagine.com/designs/bar-end-plugs

www.myminifactory.com/object/3d-print-bar-end-plugs-55776

cults3d.com/en/3d-model/tool/bar-end-plugs-stamos

See the blog post: rasterweb.net/raster/2014/09/25/3d-printing-with-wax/

Please consider a small donation to the Sanjay Mortimer Foundation to help future engineers with neurodivergent minds.

www.justgiving.com/crowdfunding/sanjay-mortimer-foundatio...

A few cupcakes, a Liberty, and a few others along the top -- lots of samples below.

3 steps 0.1 mm high, 1 mm wide. Approx 40x.

For more information see fffff.at/liberator-variations/

For 3d models see www.thingiverse.com/thing:142879

printed with my portabee 3d printer

andrew f. scott. Black Power Nkisi. FDM model. 3d scanned using Scan Studio and RapidWorks from a life cast.

Stand Orange, en partenariat avec Arketyp3d & Qbiq

Slowly working on the rear greebles.

#3Dprinting

Printed with my portabee 3d printer.

51 printed parts, printed with my portabee 3d printer

This bike was produced by 3T RPD using plastic Additive Manufacturing technology. www.3trpd.co.uk

tried out a new plastic, "PLA" behaves differently

most notably, it actually melts (phase change) where PLA just changes along a spectrum from flexible to gooey

I believe most of the scar from neck to thigh is a result of the slicer/plotter program always moving up to the next layer at nearly the same point. It is also likely, though, that some of that is exacerbated by the idle nozzle interfering with the model being printed.

(this is a "double exposure" of the same model, just rotated)

UPDATE: I was able to resolve the issue. Check here for the details. (firmware update)

Stand Orange, en partenariat avec Arketyp3d & Qbiq

Left hand side of this picture are 2 "steps" at 0.25 mm and on the right are "steps" at 0.1 mm. The transition between layers are... less regular than I'd like. Approx 40x.

"In mathematics, the Menger sponge (also known as the Menger universal curve) is a fractal curve. It is a three-dimensional generalization of the Cantor set and Sierpinski carpet. It was first described by Karl Menger in 1926, in his studies of the concept of topological dimension.

The Menger sponge simultaneously exhibits an infinite surface area and zero volume."

--from Wikipedia "Menger Sponge"

Fun with Muzz64's Sharkz model. It prints quickly... uses no supports and has moving jaw actions to clip bags, clothes, notes...or fingers!

Find the Sharkz Model on Thingiverse at www.thingiverse.com/thing:910216

View my 3D Printing Blog at www.tgaw.com

Fig 4.13 p67

Downloaded from somewhere.

Printed with my portabee 3d printer.

Not printing at the time.

Screenshots for a quick Simplify3D Tutorial.

View my 3D Printing Blog at www.tgaw.om

Fig 4.13 p67

Taylors Gregs Wades MK6 filament feed for Ultimaker (tlalexander) / CC BY 3.0

PLA filament spool ordered from Hong Kong

3D printed ironman by CustomPrototypes.

Stand Orange, en partenariat avec Arketyp3d & Qbiq