Phottix Plato - 2
Phottix recently came out with a new remote that uses 2.4GHz wireless. The Phottix Plato. It's a little pricier (~$45) but from first glance, I can see a couple of advantages over the Cleon.
[0] Digital encoding gives you a more discrete signal and helps to avoid misfires.
[1] Smart codes rolls the codes automatically to avoid contention with other remotes or RF signals.
[2] Two-way communications between receiver and transmitter confirms you are within range or not. It also seems to have a longer range.
[3] Interchangeable end-cords allows you to use the same remote on various cameras simply by replacing the connecting cord. For instance, use the N8 cord for the D300 and the N6 cord for the D80.
[4] Uses more common batteries rather than the expensive "exotic" ones the Cleon uses.
[5] Slicker looking construction.
So... I decided to get one. Tonight I came home from a business trip and found my Plato sitting in my mailbox. There were three items in the package... well five if you count the two double-packs of AAA batteries.
[0] Transmitter
[1[ Receiver
[3] Cable
Both the transmitter and receiver take common AAA batteries. This is a great improvement over some of the older Phottix and Cactus wireless remotes that took a combination of CR2 and type-N... both of which are rather expensive. There was also a single instruction sheet which was as expected written in Engrish although admittedly it's not as bad as some other products I've seen. There was however one glaring error which I will go into about later.
After installing the batteries, both the transmitter and receivers immediately power up. Shutting each of them down requires a push of their power/select button for about 3 seconds. Both have an auto-poweroff feature that shuts them off after an hour of inactivity.
Unlike previous Phottix RF remotes, this one uses rolling codes instead of choosing from amongst preset frequencies. So instead of flipping DIP switches on each device to match one another, the transmitter and receivers must be paired like bluetooth devices. The set comes pre-synced to one another from the factory but you can reset the code by resyncing them. This is accomplished by first turning on the receiver and transmitter. The transmitters picks a code. Then on the receiver, you set it to learning mode by tapping the power button five times. On the transmitter, you push the shutter release button and the two are now synced. You can sync as many as 16 million receivers to the same transmitter. The remote uses the 2.4GHz band which can get congested so in certain environments, it may take a while for the pair to negotiate with one another. But once paired the likelihood of misfires or inadvertent triggers is nearly nonexistent. There are two status LEDs on the transmitter. Half-pressing the shutter release button will confirm that you're in range by lighting them both green as well as passing a half-press action to the camera which should respond in kind (ie. activate AF and VR) depending on how the camera is configured.
The transmitter and receiver are make and model agnostic. The vendor specific interface is handled by the cable. In my case, I am using the N8 cable for the D200 and D300. One end of the cable plugs into the camera and the other end is a simple three-contact 3.5mm "headphone" style plug which can be plugged into the receiver or the transmitter. When plugged into the receiver, the transmitter is in wireless mode. If however you wish to trigger things via a wired remote, you can plug the cable into the transmitter directly. All functions are the same in either mode. Note that the instruction sheet says that it is the receiver that can be used for wired triggering operations but this is in fact incorrect.
The transmitter has two buttons. The big button is the shutter release. The smaller button is the mode select and power button. Holding down this button for about 3 seconds powers the transmitter on or off. There is a series of LEDs that indicate which type of triggering mode you've selected. The following modes are supported:
[] Single - Pressing the shutter release acts like a single press of your camera's shutter release.
[] 2s Delay - Pressing the shutter release button invokes a 2-second delay before a single release signal is sent.
[] Continuous - Pressing the shutter release button once will cause the remote to trigger five individual releases. Holding down the button will act like holding down the shutter release on your camera. The camera's behaviour will be governed by the drive-mode in such a case.
[] Bulb - Pressing the button once is the same as holding down the shutter release on the camera. Press it again to release. This is intended to be used with the bulb shutter-speed setting but if combined with any other shutter speed will act like a press once to activate and press again to release so for instance, if you are in AF-C and don't have bulb set for the shutter-speed, your camera will continue shooting until you tap the button again.
Again, half-press operation is supported and in wireless mode, the two status LEDs at the top will turn green to confirm transmitter-to-receiver signal reception. A full press will turn the two LEDs red. In wired mode only LED #1 will show status.
The receiver has a single button for on/off and learning mode selection. There are also two LEDs. In normal operation, the left most LED will repeatedly flash red to indicate that the unit is on and ready. The right LED will turn green when it receives a trigger signal from the transmitter. Putting the receiver into learning mode causes the right LED to flash rapidly. The receiver also has a hot-shoe mount so it can be conveniently secured to the flash shoe.
All in all, I'm pretty happy with this remote. It's certainly a nice improvement over the older Cleon and would highly recommend it over the Cleon line even though it's about $10 more expensive.
Phottix Plato - 2
Phottix recently came out with a new remote that uses 2.4GHz wireless. The Phottix Plato. It's a little pricier (~$45) but from first glance, I can see a couple of advantages over the Cleon.
[0] Digital encoding gives you a more discrete signal and helps to avoid misfires.
[1] Smart codes rolls the codes automatically to avoid contention with other remotes or RF signals.
[2] Two-way communications between receiver and transmitter confirms you are within range or not. It also seems to have a longer range.
[3] Interchangeable end-cords allows you to use the same remote on various cameras simply by replacing the connecting cord. For instance, use the N8 cord for the D300 and the N6 cord for the D80.
[4] Uses more common batteries rather than the expensive "exotic" ones the Cleon uses.
[5] Slicker looking construction.
So... I decided to get one. Tonight I came home from a business trip and found my Plato sitting in my mailbox. There were three items in the package... well five if you count the two double-packs of AAA batteries.
[0] Transmitter
[1[ Receiver
[3] Cable
Both the transmitter and receiver take common AAA batteries. This is a great improvement over some of the older Phottix and Cactus wireless remotes that took a combination of CR2 and type-N... both of which are rather expensive. There was also a single instruction sheet which was as expected written in Engrish although admittedly it's not as bad as some other products I've seen. There was however one glaring error which I will go into about later.
After installing the batteries, both the transmitter and receivers immediately power up. Shutting each of them down requires a push of their power/select button for about 3 seconds. Both have an auto-poweroff feature that shuts them off after an hour of inactivity.
Unlike previous Phottix RF remotes, this one uses rolling codes instead of choosing from amongst preset frequencies. So instead of flipping DIP switches on each device to match one another, the transmitter and receivers must be paired like bluetooth devices. The set comes pre-synced to one another from the factory but you can reset the code by resyncing them. This is accomplished by first turning on the receiver and transmitter. The transmitters picks a code. Then on the receiver, you set it to learning mode by tapping the power button five times. On the transmitter, you push the shutter release button and the two are now synced. You can sync as many as 16 million receivers to the same transmitter. The remote uses the 2.4GHz band which can get congested so in certain environments, it may take a while for the pair to negotiate with one another. But once paired the likelihood of misfires or inadvertent triggers is nearly nonexistent. There are two status LEDs on the transmitter. Half-pressing the shutter release button will confirm that you're in range by lighting them both green as well as passing a half-press action to the camera which should respond in kind (ie. activate AF and VR) depending on how the camera is configured.
The transmitter and receiver are make and model agnostic. The vendor specific interface is handled by the cable. In my case, I am using the N8 cable for the D200 and D300. One end of the cable plugs into the camera and the other end is a simple three-contact 3.5mm "headphone" style plug which can be plugged into the receiver or the transmitter. When plugged into the receiver, the transmitter is in wireless mode. If however you wish to trigger things via a wired remote, you can plug the cable into the transmitter directly. All functions are the same in either mode. Note that the instruction sheet says that it is the receiver that can be used for wired triggering operations but this is in fact incorrect.
The transmitter has two buttons. The big button is the shutter release. The smaller button is the mode select and power button. Holding down this button for about 3 seconds powers the transmitter on or off. There is a series of LEDs that indicate which type of triggering mode you've selected. The following modes are supported:
[] Single - Pressing the shutter release acts like a single press of your camera's shutter release.
[] 2s Delay - Pressing the shutter release button invokes a 2-second delay before a single release signal is sent.
[] Continuous - Pressing the shutter release button once will cause the remote to trigger five individual releases. Holding down the button will act like holding down the shutter release on your camera. The camera's behaviour will be governed by the drive-mode in such a case.
[] Bulb - Pressing the button once is the same as holding down the shutter release on the camera. Press it again to release. This is intended to be used with the bulb shutter-speed setting but if combined with any other shutter speed will act like a press once to activate and press again to release so for instance, if you are in AF-C and don't have bulb set for the shutter-speed, your camera will continue shooting until you tap the button again.
Again, half-press operation is supported and in wireless mode, the two status LEDs at the top will turn green to confirm transmitter-to-receiver signal reception. A full press will turn the two LEDs red. In wired mode only LED #1 will show status.
The receiver has a single button for on/off and learning mode selection. There are also two LEDs. In normal operation, the left most LED will repeatedly flash red to indicate that the unit is on and ready. The right LED will turn green when it receives a trigger signal from the transmitter. Putting the receiver into learning mode causes the right LED to flash rapidly. The receiver also has a hot-shoe mount so it can be conveniently secured to the flash shoe.
All in all, I'm pretty happy with this remote. It's certainly a nice improvement over the older Cleon and would highly recommend it over the Cleon line even though it's about $10 more expensive.