View allAll Photos Tagged module
As per the placecard, a module of cotton contains about 12-15 bales of cotton and a bale of cotton weighs about 500 lbs. That's a lot of cotton! This thing was as hard as a rock
A session this evening with my Module 2 portrait model Vanessa. This time I have her running. I did deliberately take some street scene shots. Is this bad? I don't know. People do run in places other than with clean backgrounds. Would I be brave enough to submit it though? Again I don't know. I feel a deadline looming and I'm not sure what I'm doing yet. My dog shots were rubbish (didn't bother to upload), and my horse shots never happened as the horse went lame.
The rest of my photos from this session can be found here if you have the time to look
My final attempt at this module. I remembered that we had some childrens' skittles and after a few experiments managed to get the timing and settings right.
Nothing to do. SO i took a picture of my timetable..this is the modules i'm taking this semester. see how 'finance' it is..
success! I ran out of time to solder it up but it came out as good as I can hope for. No noticeable 'erosion' of traces. Alignment between the two sides is good enough. This could be close to my final layout. I'm excited!
Stackable modules for my Soropolis project.
Owlery - Crockery - dog attic - ostrich tower - sheep fold - flower girl - chicken run - monkey attic - horse stable - South Pole
These are the diagrams for the decagon cross module.
Nothing really new. As I have explained at the octagon cross module:
If you want to double the corners of the polygon, then you have to bisect to important angle for the inside reverse fold (step 2).
So start here with the Pentagon Cross module.
The steps 7 to 11 are just for hidding some paper. You can do it also in other ways to get some variations. The width of the flap shouldn't be wider than the width of the pocket.
The assembly of the modules is similar to the assembly of the square cross modules, here only with ten modules.
The angle at step 5 has not exact 72 degrees, but the approximation with 71.98 degrees is close to it.
Now, can you see the way to the icosagon ??
Stackable modules for my Soropolis project.
Two boys having a coffee - raven appartment - vampire - bird tower - temple - gold dome - ghost cave - monster cave - mosque - lady and pooch having a coffee - volcano
Second Lunar Module built. Was not designed to make the trip to the Moon or support astronauts but for an unmanned Earth orbital test.
Combo module using a visaton speaker and a TDA2030 amplifier IC. This is the 1st one, i will build a 2nd one, both are for my 9U portable system.
Layout module for Kanimbla station under construction using laminated pine board, with pine skirts and bracing screwed underneath. The island platform is also pine and screwed to the top. Cut through the board are openings for points drives, signals and electromagnetic uncouplers, with cork roadbed laid over the top. End walls are temporary to protect the module from damage.
A Lunar Module from the Apollo program (designed and built by Grumman)
National Air & Space Museum (Washington DC)
Photo by www.kensaviation.com
Scanned from 35mm slide (1980)
Part of a (slow) process of digitalizing my old photos
Think you could land this on the moon? This is a mockup of the lunar module that landed on the moon between 1969–1972. it carried two people. 6 landings on the moon were made.
The Zeplina Power Module was created to power the worlds largest zeppelin, this piece was destined for stardom as an epic event in history. However, its extreme weight and the fact it was mounted at the front of the zeppelin meant that the nose couldn't get of the ground, even with the excessive amount of power it produced. The zeppelin cruised along, bum in the air, nose to the ground like a dog sniffing out the trail of dragged sausages. The zeppelin company refused to pay for the item, so I turned it into a lamp and this (almost) piece of history is for sale!
The "Y Module" was created in 1988 and published in "Modular Origami" a self-publication. The module, folded from square papers is based on the 60 degree geometry. When assembled, a "Y" band is form on the triangular faces of the model and a small pinwheel motif on all the corners.
3 of the 5 Platonic Solids can be assembled from this module. They are the Tetrahedron, the Octahedron and the Icosahedron. All of these polyhedra have triangular faces.
30 Modules, folded from 15cm square Kami are used to assemble the Icosahedron.
Prius 2nd Generation Battery Module. Popped its top going up a hill. This was one of 38 modules in a rebuild Generation 1 battery pack. Replaced it but I suspect I have other modules in failure mode. Bummer, but you get what you get when buying off Epray (Ebay).
Development Impact and the PhD Scholarship - Tool Kit training held at Cumberland Lodge, Windsor from 30 July - 1 August 2014
This is my version of the Hendecagon Cross module.
The angle for the exact hendecagon has 73.64 degrees. My approximation here has 73.66 degrees. It is quite close to it.
The steps 10 to 14 are just for hidding some paper. You can do it also in other ways to get some variations. The width of the flap shouldn't be wider than the width of the pocket.
The assembly of the modules is similar to the assembly of the square cross modules, here only with eleven modules.