View allAll Photos Tagged crossslide
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley. This is in the boonies of Northern CA.
The label reads:
The Muller Lathe
Built by
The Bradford Mill Co.
Cincinatti, Ohio
USA
The size is as follows, roughly measured:
Swing over bed: 20"
Swing over carriage: unknown
Four-jaw chuck diameter: 18"
Bed length: 12 feet
Bed width, center to center across the outer two ways: 16”
Maximum workpiece length, center to center: 8 feet
It may have been built in the 1886-1901 era, from what I've learned so far.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description. My girlfriend Zoe bought a 1955 Carpenter (1954 GMC based) school bus from him, and he towed it the 17 miles to our Ranch with his old tractor on public roads:
www.youtube.com/watch?v=vihuX5mIFSA
Photos of the bus can be seen in another set of mine:
www.flickr.com/photos/darronb/sets/72157635098965316/
Willie also renovates and runs old steam engines. His tools are basic and in, umm, often less than pretty condition.
I believe he told me that despite its condition, having been outside for many years, this lathe was still in occasional use, wonder of wonders. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to list it for sale soon, online. If nothing else, it makes a magnificent lawn ornament.
Almost all of the images in this set were 3-exp HDRs, processed with Photomatix. The camera was a Nikon D50.
More info on Bradford lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley. This is in the boonies of Northern CA.
The label reads:
The Muller Lathe
Built by
The Bradford Mill Co.
Cincinatti, Ohio
USA
The size is as follows, roughly measured:
Swing over bed: 20"
Swing over carriage: unknown
Four-jaw chuck diameter: 18"
Bed length: 12 feet
Bed width, center to center across the outer two ways: 16”
Maximum workpiece length, center to center: 8 feet
It may have been built in the 1886-1901 era, from what I've learned so far.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description. My girlfriend Zoe bought a 1955 Carpenter (1954 GMC based) school bus from him, and he towed it the 17 miles to our Ranch with his old tractor on public roads:
www.youtube.com/watch?v=vihuX5mIFSA
Photos of the bus can be seen in another set of mine:
www.flickr.com/photos/darronb/sets/72157635098965316/
Willie also renovates and runs old steam engines. His tools are basic and in, umm, often less than pretty condition.
I believe he told me that despite its condition, having been outside for many years, this lathe was still in occasional use, wonder of wonders. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to list it for sale soon, online. If nothing else, it makes a magnificent lawn ornament.
Almost all of the images in this set were 3-exp HDRs, processed with Photomatix. The camera was a Nikon D50.
More info on Bradford lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This large and ancient metal lathe is located in Lookout, California, in Lassen County, Big Valley.
This is in the boonies of Northern CA.
The label reads:
The Hendey Machine Co. Torrington Conn. U.S.A.
The size is as follows:
Swing over bed: 18"
Swing over carriage: unknown
Chuck diameter: unknown
Bed length: 10 feet
It may have been built in the 1905-1920 era, from what I've learned so far.
It has a full feed/threading gearbox.
It is equipped with at least parts of a taper attachment.
The original drive, which may have been a lineshaft or an electric motor is long gone. In its place, a modern 1HP motor with an unknown number of poles drives the conehead through a three-speed automotive transmission and a flat belt to the spindle cone. The owner says the motor will start the spindle in anything but highest gear.
It is owned by a fine older gentleman named Willie. He owns a LARGE property full of old tractors, cars, trucks, bulldozers and vehicles of varied and sundry description.
This lathe was still in occasional use. I expect that it could be restored to its former glory by a man willing and able to put a LOT of time and/or money into it. I plan to buy it some day, assuming Willie gets tired of it at some point.
More info on Hendey lathes:
This is the knob and dial on the cross-slide leadscrew of my late 1960s Clausing model 5912 engine lathe.
12.25-inch swing, 36-inches between centers.
Highly processed single-exposure pseudo-HDR image.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.
We find that Craft & Design pupils often have difficulty remembering the sequence of operations involved when making a simple screwdriver handle. These photographs depict this process.
We begin with the preparation of the 25mm aluminium blank. After this the blank is held in the 3 jaw self centering chuck. A series of turning operations is then carried out. For the following we set a high spindle speed and used a slow feed speed for best results. Shown here we show facing off. Then turning down or parallel turning. Next taper turning. After that the Slocombe bit or centre bit is mounted in a Jacob's chuck and a pilot hole is drilled. A HSS twist drill or jobber bit is then mounted in the Jacob's chuck and a blind hole is drilled to a depth of 30mm. The depth gauge is used to judge this.
Taps and dies are used to cut the internal thread on the screwdriver blade and the internal thread on the handle.
Finally both components are assembled and the handle is knurled or given a textured grip pattern. This is done at a very low spindle speed and a slow automatic feed speed.