View allAll Photos Tagged Sowerby_bridge
A three car Class 110 with car no. E52078 leading, leaves Sowerby Bridge with 2E11 10:55 Manchester Victoria to York. 11/9/86.
Twenty five minutes after the previous photo, 47119 is dwarfed by the buildings of Sowerby Bridge as it passes through the town with 6M14 Lindsey to Glazebrook loaded tanks. 27/11/87.
47402 "Gateshead" races through Sowerby Bridge on the 31st January 1988 with the diverted 1M63 08:00 Newcastle to Liverpool Lime Street. Note the two guys walking along with guns and dogs to the right of the photo. If they were doing it now they'd be walking through the station car park, which was greatly extended a few years ago.
My little Sony camera did a good job with no need for 'sunset' settings or computer retouching. One of the few times in dodgy light when my camera can beat my wife's iPhone! This is the east end of the Rochdale Canal and is the start of a project to photograph every lock, bridge and major canal-side feature on this waterway. All the photos have now been uploaded.
The Rochdale Canal in Todmorden, Calderdale, West Yorkshire.
It is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire.
The Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first two attempts to obtain an act failed after being opposed by mill owners, concerned about water supply. The promoters, to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and in 1794 an act was obtained which created the Rochdale Canal Company and its construction.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974.
The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park. They worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal. However, the plan was rejected by the Commission, and to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal.
Information Source:
The Rochdale Canal in approaching Todmorden in Calderdale, West Yorkshire.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles (51 km) across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire. As built, the canal had 92 locks. Whilst the traditional lock numbering has been retained on all restored locks, and on the relocated locks, the canal now has 91. Locks 3 and 4 have been replaced with a single deep lock, Tuel Lane Lock, which is numbered 3/4.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester. Brindley proposed a route similar to the one built, and another more expensive route via Bury. Further progress was not made until 1791, when John Rennie was asked to make a new survey in June, and two months later to make surveys for branches to Rochdale, Oldham and to a limeworks near Todmorden. Rennie at the time had no experience of building canals.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first attempt to obtain an act was made in 1792, but was opposed by mill owners, concerned about water supply. Rennie proposed using steam pumping engines, three in Yorkshire, eight in Lancashire, and one on the Burnley Branch, but the mill owners argued that 59 mills would be affected by the scheme, resulting in unemployment, and the bill was defeated. In September 1792, William Crosley and John Longbotham surveyed the area in an attempt to find locations for reservoirs which would not affect water supplies to the mills. A second bill was presented to Parliament, for a canal which would have a 3,000-yard (2,700 m) tunnel and 11 reservoirs. Again the bill was defeated, this time by one vote. The promoters, in an attempt to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and on 4 April 1794 an act was obtained which created the Rochdale Canal Company and authorised construction.
Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required. The estimate was for a narrow canal, whereas the act authorised a broad canal, and so the capital was never going to be adequate. The summit tunnel was abandoned in favour of 14 additional locks saving £20,000. Jessop proposed constructing each lock with a drop of 10 feet (3.0 m), resulting in efficient use of water and the need to manufacture only one size of lock gate.
The canal opened in stages as sections were completed, with the Rochdale Branch the first in 1798 and further sections in 1799. The bottom nine locks opened in 1800 and boats using the Ashton Canal could reach Manchester. Officially, the canal opened in 1804, but construction work continued for more three years. A 1.5-mile (2.4 km) branch from Heywood to Castleton opened in 1834.
Apart from a short profitable section in Manchester linking the Bridgewater and Ashton Canals, most of the length was closed in 1952 when an act of parliament was obtained to ban public navigation. The last complete journey had taken place in 1937, and by the mid 1960s the remainder was almost unusable. Construction of the M62 motorway in the late 1960s took no account of the canal, cutting it in two.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974. The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park
The Rochdale Canal Society worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust Ltd, who leased the canal from the owning company. The MSC-funded restoration was approaching Sowerby Bridge, where planners were proposing a tunnel and deep lock to negotiate a difficult road junction at Tuel Lane, so that a connection could be made with the Calder and Hebble Navigation. The entire eastern section from Sowerby Bridge to the summit at Longlees was open by 1990, although it remained isolated from the canal network.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal from the Rochdale Canal Company. However, the plan was rejected by the Commission, and in order to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal. As restoration proceeded, boats could travel further and further west, and the restoration of the sections through Failsworth and Ancoats were a significant part of the re-development of the north Manchester districts. The restored sections joined up with the section in Manchester below the Ashton Canal junction, which had never been closed, and on 1 July 2002 the canal was open for navigation along its entire length.
Best viewed Original size.
An unidentifiable 3-car BRCW Class 110 "Calder Valley" DMU passes Milner Royd signal box with a local service for Manchester - 03/09/1986.
Please do not share or post elsewhere without the permission of the copyright owner(s).
© 2019 - 53A Models of Hull Collection. Scanned from the original 35mm colour transparency.
- - - - - -
56101 heads down the Calder Valley at Sowerby Bridge with Fiddlers Ferry to Healey Mills MGR empties. 30/9/86.
Looking from Shaw Wood Bridge along Shawplains Lock on the Rochdale Canal outside Todmorden, in Calderdale, West Yorkshire.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles (51 km) across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire. As built, the canal had 92 locks. Whilst the traditional lock numbering has been retained on all restored locks, and on the relocated locks, the canal now has 91. Locks 3 and 4 have been replaced with a single deep lock, Tuel Lane Lock, which is numbered 3/4.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester. Brindley proposed a route similar to the one built, and another more expensive route via Bury. Further progress was not made until 1791, when John Rennie was asked to make a new survey in June, and two months later to make surveys for branches to Rochdale, Oldham and to a limeworks near Todmorden. Rennie at the time had no experience of building canals.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first attempt to obtain an act was made in 1792, but was opposed by mill owners, concerned about water supply. Rennie proposed using steam pumping engines, three in Yorkshire, eight in Lancashire, and one on the Burnley Branch, but the mill owners argued that 59 mills would be affected by the scheme, resulting in unemployment, and the bill was defeated. In September 1792, William Crosley and John Longbotham surveyed the area in an attempt to find locations for reservoirs which would not affect water supplies to the mills. A second bill was presented to Parliament, for a canal which would have a 3,000-yard (2,700 m) tunnel and 11 reservoirs. Again the bill was defeated, this time by one vote. The promoters, in an attempt to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and on 4 April 1794 an act was obtained which created the Rochdale Canal Company and authorised construction.
Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required. The estimate was for a narrow canal, whereas the act authorised a broad canal, and so the capital was never going to be adequate. The summit tunnel was abandoned in favour of 14 additional locks saving £20,000. Jessop proposed constructing each lock with a drop of 10 feet (3.0 m), resulting in efficient use of water and the need to manufacture only one size of lock gate.
The canal opened in stages as sections were completed, with the Rochdale Branch the first in 1798 and further sections in 1799. The bottom nine locks opened in 1800 and boats using the Ashton Canal could reach Manchester. Officially, the canal opened in 1804, but construction work continued for more three years. A 1.5-mile (2.4 km) branch from Heywood to Castleton opened in 1834.
Apart from a short profitable section in Manchester linking the Bridgewater and Ashton Canals, most of the length was closed in 1952 when an act of parliament was obtained to ban public navigation. The last complete journey had taken place in 1937, and by the mid 1960s the remainder was almost unusable. Construction of the M62 motorway in the late 1960s took no account of the canal, cutting it in two.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974. The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park
The Rochdale Canal Society worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust Ltd, who leased the canal from the owning company. The MSC-funded restoration was approaching Sowerby Bridge, where planners were proposing a tunnel and deep lock to negotiate a difficult road junction at Tuel Lane, so that a connection could be made with the Calder and Hebble Navigation. The entire eastern section from Sowerby Bridge to the summit at Longlees was open by 1990, although it remained isolated from the canal network.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal from the Rochdale Canal Company. However, the plan was rejected by the Commission, and in order to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal. As restoration proceeded, boats could travel further and further west, and the restoration of the sections through Failsworth and Ancoats were a significant part of the re-development of the north Manchester districts. The restored sections joined up with the section in Manchester below the Ashton Canal junction, which had never been closed, and on 1 July 2002 the canal was open for navigation along its entire length.
A Class 104 DMU leads a Class 105 away from Sowerby Bridge forming 2M18 12:26 York to Manchester Victoria. 8/10/86 (14:08)
56110 has just passed Sowerby Bridge station with 6E56 Fiddlers Ferry to Healey Mills empty MGR. 3/10/86.
Walking alongside the Rochdale Canal approaching the Grade II Listed Woodhouse Mill Bridge and the Grade II* Listed Woodhouse Mill, in Todmorden, Calderdale, West Yorkshire.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles (51 km) across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire. As built, the canal had 92 locks. Whilst the traditional lock numbering has been retained on all restored locks, and on the relocated locks, the canal now has 91. Locks 3 and 4 have been replaced with a single deep lock, Tuel Lane Lock, which is numbered 3/4.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester. Brindley proposed a route similar to the one built, and another more expensive route via Bury. Further progress was not made until 1791, when John Rennie was asked to make a new survey in June, and two months later to make surveys for branches to Rochdale, Oldham and to a limeworks near Todmorden. Rennie at the time had no experience of building canals.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first attempt to obtain an act was made in 1792, but was opposed by mill owners, concerned about water supply. Rennie proposed using steam pumping engines, three in Yorkshire, eight in Lancashire, and one on the Burnley Branch, but the mill owners argued that 59 mills would be affected by the scheme, resulting in unemployment, and the bill was defeated. In September 1792, William Crosley and John Longbotham surveyed the area in an attempt to find locations for reservoirs which would not affect water supplies to the mills. A second bill was presented to Parliament, for a canal which would have a 3,000-yard (2,700 m) tunnel and 11 reservoirs. Again the bill was defeated, this time by one vote. The promoters, in an attempt to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and on 4 April 1794 an act was obtained which created the Rochdale Canal Company and authorised construction.
Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required. The estimate was for a narrow canal, whereas the act authorised a broad canal, and so the capital was never going to be adequate. The summit tunnel was abandoned in favour of 14 additional locks saving £20,000. Jessop proposed constructing each lock with a drop of 10 feet (3.0 m), resulting in efficient use of water and the need to manufacture only one size of lock gate.
The canal opened in stages as sections were completed, with the Rochdale Branch the first in 1798 and further sections in 1799. The bottom nine locks opened in 1800 and boats using the Ashton Canal could reach Manchester. Officially, the canal opened in 1804, but construction work continued for more three years. A 1.5-mile (2.4 km) branch from Heywood to Castleton opened in 1834.
Apart from a short profitable section in Manchester linking the Bridgewater and Ashton Canals, most of the length was closed in 1952 when an act of parliament was obtained to ban public navigation. The last complete journey had taken place in 1937, and by the mid 1960s the remainder was almost unusable. Construction of the M62 motorway in the late 1960s took no account of the canal, cutting it in two.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974. The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park
The Rochdale Canal Society worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust Ltd, who leased the canal from the owning company. The MSC-funded restoration was approaching Sowerby Bridge, where planners were proposing a tunnel and deep lock to negotiate a difficult road junction at Tuel Lane, so that a connection could be made with the Calder and Hebble Navigation. The entire eastern section from Sowerby Bridge to the summit at Longlees was open by 1990, although it remained isolated from the canal network.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal from the Rochdale Canal Company. However, the plan was rejected by the Commission, and in order to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal. As restoration proceeded, boats could travel further and further west, and the restoration of the sections through Failsworth and Ancoats were a significant part of the re-development of the north Manchester districts. The restored sections joined up with the section in Manchester below the Ashton Canal junction, which had never been closed, and on 1 July 2002 the canal was open for navigation along its entire length.
Approaching Deansgate Railway Bridge on the Rochdale Canal in Castlefield, Manchester, Greater Manchester.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles (51 km) across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire. As built, the canal had 92 locks. Whilst the traditional lock numbering has been retained on all restored locks, and on the relocated locks, the canal now has 91. Locks 3 and 4 have been replaced with a single deep lock, Tuel Lane Lock, which is numbered 3/4.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester. Brindley proposed a route similar to the one built, and another more expensive route via Bury. Further progress was not made until 1791, when John Rennie was asked to make a new survey in June, and two months later to make surveys for branches to Rochdale, Oldham and to a limeworks near Todmorden. Rennie at the time had no experience of building canals.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first attempt to obtain an act was made in 1792, but was opposed by mill owners, concerned about water supply. Rennie proposed using steam pumping engines, three in Yorkshire, eight in Lancashire, and one on the Burnley Branch, but the mill owners argued that 59 mills would be affected by the scheme, resulting in unemployment, and the bill was defeated. In September 1792, William Crosley and John Longbotham surveyed the area in an attempt to find locations for reservoirs which would not affect water supplies to the mills. A second bill was presented to Parliament, for a canal which would have a 3,000-yard (2,700 m) tunnel and 11 reservoirs. Again the bill was defeated, this time by one vote. The promoters, in an attempt to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and on 4 April 1794 an act was obtained which created the Rochdale Canal Company and authorised construction.
Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required. The estimate was for a narrow canal, whereas the act authorised a broad canal, and so the capital was never going to be adequate. The summit tunnel was abandoned in favour of 14 additional locks saving £20,000. Jessop proposed constructing each lock with a drop of 10 feet (3.0 m), resulting in efficient use of water and the need to manufacture only one size of lock gate.
The canal opened in stages as sections were completed, with the Rochdale Branch the first in 1798 and further sections in 1799. The bottom nine locks opened in 1800 and boats using the Ashton Canal could reach Manchester. Officially, the canal opened in 1804, but construction work continued for more three years. A 1.5-mile (2.4 km) branch from Heywood to Castleton opened in 1834.
Apart from a short profitable section in Manchester linking the Bridgewater and Ashton Canals, most of the length was closed in 1952 when an act of parliament was obtained to ban public navigation. The last complete journey had taken place in 1937, and by the mid 1960s the remainder was almost unusable. Construction of the M62 motorway in the late 1960s took no account of the canal, cutting it in two.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974. The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park
The Rochdale Canal Society worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust Ltd, who leased the canal from the owning company. The MSC-funded restoration was approaching Sowerby Bridge, where planners were proposing a tunnel and deep lock to negotiate a difficult road junction at Tuel Lane, so that a connection could be made with the Calder and Hebble Navigation. The entire eastern section from Sowerby Bridge to the summit at Longlees was open by 1990, although it remained isolated from the canal network.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal from the Rochdale Canal Company. However, the plan was rejected by the Commission, and in order to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal. As restoration proceeded, boats could travel further and further west, and the restoration of the sections through Failsworth and Ancoats were a significant part of the re-development of the north Manchester districts. The restored sections joined up with the section in Manchester below the Ashton Canal junction, which had never been closed, and on 1 July 2002 the canal was open for navigation along its entire length.
158901 approaches Sowerby Bridge station with the 16:47 York to Liverpool Lime Street service. 21/8/91. Lovely open spaces here at the time. Nowadays, it's trees everywhere - so tall you can't see Wainhouse Tower and the area behind the unit is now the extended station car park topped of with a comms mast. Ruined!
First attempt of light trails using the dji phantom. 6 Second shot. A little blurry but surprised i managed to get the shot
The Calder and Hebble Navigation, a canal in Halifax, Calderdale, West Yorkshire.
By the beginning of the 18th century, the Aire and Calder Navigation had made the River Calder navigable as far upstream as Wakefield. The aim of the Calder and Hebble Navigation was to extend navigation west (upstream) from Wakefield to Sowerby Bridge near Halifax.
The first attempt to obtain an Act of Parliament was made in 1740, as a result of a petition by the people of Halifax, Ripponden and Elland. John Eyes of Liverpool surveyed the route, and presented a scheme for a navigation which would use the River Calder from Wakefield to its junction with the River Hebble, follow the Hebble to Salterhebble Bridge, and then follow the Halifax Brook to reach Halifax. The bill was defeated, due to opposition from local landowners who feared that it would cause flooding, from millers, who thought that navigation would disrupt their water supply, and from the promoters of several Turnpike Bills, who were intending to build roads which would follow a similar route.
The second attempt followed a meeting of the Union Club in Halifax on 2 September 1756, which considered how to improve the import of wool and corn to the town. They invited the civil engineer John Smeaton to make a new survey, which he did in late 1757. An Act was obtained on 9 June 1758, for this extended route, and created Commissioners, who must own an estate valued at more than £100, or have a personal fortune of more than £3,000.
Construction started in November 1759, with Smeaton acting as engineer. By November 1764, the navigation was open as far as Brighouse, some 16 miles (26 km) from Wakefield. Having borrowed £56,000, factions arose within the Commissioners, with some wanting to stop at Brooksmouth, where the Rivers Hebble and Calder meet, and others wanting to raise more money and complete the scheme. The second option gained most support, and a new committee was set up, who asked James Brindley to take over from Smeaton in 1765. The work was just complete when a further flood caused so much damage that the only option was to close the navigation again.
The Commissioners felt unable to borrow more money, and so a second Act of Parliament was obtained on 21 April 1769, which formally created the Company of Proprietors of the Calder and Hebble Navigation. This consisted of all of the 81 people who had loaned money to the original scheme, and these loans were converted into £100 shares. Additional shares could be issued, and the Company could borrow up to £20,000, with the future tolls used as security.
The Navigation prospered, with dividends rising steadily from 5 per cent in 1771 to 13 per cent in 1792. Under the terms of the Act of Parliament, tolls were reduced when the dividend exceeded 10 per cent, and the first such reduction occurred in 1791.
In 1798 a long cut at Thornhill was made, bypassing the town of Dewsbury. Trade with the town was maintained by the construction of a new branch from Thornhill to Dewsbury. Another stimulus to trade was provided by the Rochdale Canal, which opened up a through route from Sowerby Bridge to Manchester from 1804.
The Manchester and Leeds Railway company, which had approached the Calder and Hebble in 1836, but had been rebuffed, opened their line between 1839 and 1841. It followed the line of the canal and that of the Rochdale Canal. A year later, with canal shares having lost 66 per cent of their value, the canal company approached the railway, who agreed to lease the canal for £40,000 per year for 14 years, commencing on 25 March 1843. The Aire and Calder Navigation objected to the lease, and in April 1847, the Attorney General and the Solicitor General ruled that it was illegal, and must cease. Soon afterwaards, the Aire and Calder offered to lease the canal itself, and the agreement started in September. After the Aire and Calder's lease expired in 1885, the Navigation Company again took charge, rebuilt many of the bridges, and established the Calder Carrying Company. Shareholders continued to receive dividends until the canal was nationalized in 1948, and the canal was used by commercial traffic until 1981.
By the Rochdale Canal. The octagonal chimney was sadly demolished in the early 2000s and just the base remains.
Sowerby Bridge Lock Moorings on the Rochdale Canal in Sowerby Bridge, Calderdale, West Yorkshire.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles (51 km) across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire. As built, the canal had 92 locks. Whilst the traditional lock numbering has been retained on all restored locks, and on the relocated locks, the canal now has 91. Locks 3 and 4 have been replaced with a single deep lock, Tuel Lane Lock, which is numbered 3/4.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester. Brindley proposed a route similar to the one built, and another more expensive route via Bury. Further progress was not made until 1791, when John Rennie was asked to make a new survey in June, and two months later to make surveys for branches to Rochdale, Oldham and to a limeworks near Todmorden. Rennie at the time had no experience of building canals.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first attempt to obtain an act was made in 1792, but was opposed by mill owners, concerned about water supply. Rennie proposed using steam pumping engines, three in Yorkshire, eight in Lancashire, and one on the Burnley Branch, but the mill owners argued that 59 mills would be affected by the scheme, resulting in unemployment, and the bill was defeated. In September 1792, William Crosley and John Longbotham surveyed the area in an attempt to find locations for reservoirs which would not affect water supplies to the mills. A second bill was presented to Parliament, for a canal which would have a 3,000-yard (2,700 m) tunnel and 11 reservoirs. Again the bill was defeated, this time by one vote. The promoters, in an attempt to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and on 4 April 1794 an act was obtained which created the Rochdale Canal Company and authorised construction.
Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required. The estimate was for a narrow canal, whereas the act authorised a broad canal, and so the capital was never going to be adequate. The summit tunnel was abandoned in favour of 14 additional locks saving £20,000. Jessop proposed constructing each lock with a drop of 10 feet (3.0 m), resulting in efficient use of water and the need to manufacture only one size of lock gate.
The canal opened in stages as sections were completed, with the Rochdale Branch the first in 1798 and further sections in 1799. The bottom nine locks opened in 1800 and boats using the Ashton Canal could reach Manchester. Officially, the canal opened in 1804, but construction work continued for more three years. A 1.5-mile (2.4 km) branch from Heywood to Castleton opened in 1834.
Apart from a short profitable section in Manchester linking the Bridgewater and Ashton Canals, most of the length was closed in 1952 when an act of parliament was obtained to ban public navigation. The last complete journey had taken place in 1937, and by the mid 1960s the remainder was almost unusable. Construction of the M62 motorway in the late 1960s took no account of the canal, cutting it in two.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974. The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park
The Rochdale Canal Society worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust Ltd, who leased the canal from the owning company. The MSC-funded restoration was approaching Sowerby Bridge, where planners were proposing a tunnel and deep lock to negotiate a difficult road junction at Tuel Lane, so that a connection could be made with the Calder and Hebble Navigation. The entire eastern section from Sowerby Bridge to the summit at Longlees was open by 1990, although it remained isolated from the canal network.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal from the Rochdale Canal Company. However, the plan was rejected by the Commission, and in order to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal. As restoration proceeded, boats could travel further and further west, and the restoration of the sections through Failsworth and Ancoats were a significant part of the re-development of the north Manchester districts. The restored sections joined up with the section in Manchester below the Ashton Canal junction, which had never been closed, and on 1 July 2002 the canal was open for navigation along its entire length.
The Rochdale Canal in Sowerby Bridge, Calderdale, West Yorkshire.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first two attempts to obtain an act failed after being opposed by mill owners, concerned about water supply. The promoters, to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and in 1794 an act was obtained which created the Rochdale Canal Company and its construction. Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974.
The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park. They worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal. However, the plan was rejected by the Commission, and to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal.
Information Source:
The Rochdale Canal in Manchester, Greater Manchester.
The Rochdale is a broad canal because its locks are wide enough to allow vessels of 14 feet width. The canal runs for 32 miles across the Pennines from the Bridgewater Canal at Castlefield Basin in Manchester to join the Calder and Hebble Navigation at Sowerby Bridge in West Yorkshire.
The Rochdale Canal was conceived in 1776, when a group of 48 men from Rochdale raised £237 and commissioned James Brindley to conduct a survey of possible routes between Sowerby Bridge and Manchester.
The promoters, unsure as to whether to build a wide or a narrow canal, postponed the decision until an Act of Parliament had been obtained. The first two attempts to obtain an act failed after being opposed by mill owners, concerned about water supply. The promoters, to understand the mill owners' position, asked William Jessop to survey the parts of the proposed canal that were causing most concern. Jessop gave evidence to the Parliamentary committee, and in 1794 an act was obtained which created the Rochdale Canal Company and its construction. Rennie's estimated cost in the second bill was £291,000, and the company was empowered to raise the money by issuing shares, with powers to raise a further £100,000 if required.
When an Act of Parliament was sought in 1965, to authorise the abandonment of the canal, the Inland Waterways Association petitioned against it, and when it was finally passed, it contained a clause that ensured the owners would maintain it until the adjacent Ashton Canal was abandoned. Discussion of the relative merits of restoring the canal or the Huddersfield Narrow Canal in 1973 led the formation of societies to promote both schemes in 1974.
The Rochdale Canal Society wanted to see the canal fully re-opened, as part of a proposed Pennine Park. They worked hard both to protect the line of the canal and to begin the process of refurbishing it. A new organisational structure was created in 1984, with the formation of the Rochdale Canal Trust.
In 1997, the Rochdale Canal Trust was restructured, in response to announcements that there might be large grants available as part of the millennium celebrations. The canal was still at this point owned by a private company, and the Millennium Commission would not make grants to a scheme which was for private profit, rather than public benefit. The restructuring would allow the Trust to take over responsibility for the canal. However, the plan was rejected by the Commission, and to access the grant of £11.3 million, the Waterways Trust took over ownership of the canal.
Information Source:
Twin Valley B10 WTN is leaving the Yorkshire Wildlife Park in Doncaster, It is a Volvo B10M with Plaxton Premiere 350 coachwork which was new to Elcock, Madeley in 1997 registered P288 ENT. It later ran for Woottens, Lye Green (where it became B10 WTN) and Emblings/Judds, Guyhirn and retains the livery of the latter.