20190103 John - Haulpak Field Engineer
HAULPAK 930E-4SE ENGINE SPECIFICATION
Make and model . . . . . . . . . . . . . . . . . . . . . . Komatsu SSDA18V170
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operating cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 cycle
Gross horsepower . . . . . . . . . . . . . 2611 kW 3,500 HP @ 1900 rpm
Net flywheel power* . . . . . . . . . . . . 2558 kW 3,429 HP @ 1900 rpm
Weight (wet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10100 kg 22,266 lb
* Net flywheel power is the rated power at the engine flywheel minus the average accessory losses. Accessories include fan and charging alternator.
Power ratings above represent engine performance in accordance with SAE J1995 and J1349 conditions.
930E-4SE ELECTRIC DRIVE
AC CURRENT
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GTA-39
Dual impeller in-line blower . . . . . . . . . . . 453 m3 /min 16,000 cfm
Control . . . . . . . . . . . . . . . . . . . . . . . . . AC Torque Control System
Motorized wheels*. . . . . . . GDY106 AC Induction Traction Motors
Ratio** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32.62:1
Speed (maximum) . . . . . . . . . . . . . . . . . . . . . . 64.5 km/h 40 mph
* Wheel motor application depends upon gross vehicle weight, haul road grade, haul road length, rolling resistance and other parameters. Komatsu and G.E. must analyze each job condition to assure proper application.
** Optional ratios available.
930E-4SE TIRES AND RIMS
Rock service, tubeless, radial tires
Standard tire* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53/80 R63 Taper Lock
914 mm x 1600 mm x 127 mm 36'' x 63'' x 5.0'' rim assembly
Rated at 758 kPa 110 psi cold inflation pressure for rims, 600 kPa 87 psi for tires.
* Tires should meet application requirements for tkph/tmph, tread, compound, inflation pressure, ply rating or equivalent, etc.
930E-4SE BODY
All-welded steel flat floor body with horizontal bolsters and full canopy. Eyebrow, rear wheel rock ejectors, body up sling, and rubber mounts on frame are standard. Pivot exhaust heating optional.
Floor sheet . . . . . . . . . . . . . 16 mm 0.63'' 1379 MPa 200,000 psi tensile strength steel (two-piece)
Front sheet . . . . . . . . . . . . . . 9 mm 0.35'' 1379 MPa 200,000 psi tensile strength steel
Side sheet . . . . . . . . . . . . . . 8 mm 0.31'' 1379 MPa 200,000 psi tensile strength steel
Canopy sheet . . . . . . . . . . . . . 5 mm 0.19'' 690 MPa 100,000 psi tensile strength steel
Standard SAE heaped 2:1. . . . . . . . . . . . . . . . . . . 211 m3 276 yd3
Standard Komatsu body weight . . . . . . . . . . . 30362 kg 66,936 lb
* Komatsu must approve all bodies through a Body Application Worksheet.
930E-4SE CAB
Advanced Operator Environment with integral 4-post ROPS/FOPS structure (meets J1040 Apr88), adjustable air suspension seat w/lumbar support and arm rests, passenger seat, maximum R-value insulation, tilt and telescoping steering wheel, electric windshield wipers w/washer, tinted safety glass, power windows, Komatsu Payload Weighing System, 55,000 Btu/hr heater and defroster, 21,600 Btu/hr air conditioning (HFC - 134A refrigerant).
930E-4SE FRAME
Advanced technology, full butt-welded box sectional ladder-type frame with integral ROPS supports, integral front bumper, rear tubular cross members, steel castings at all critical stress transition zones, rugged continuous horsecollar.
Plate material . . . . . . . . . . . . . . . . . . . . . . . . 482.6 MPa 70,000 psi tensile strength steel
Casting material . . . . . . . . . . . . . . . . . . . . . . 620.5 MPa 90,000 psi tensile strength steel
Rail width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 mm 12''
Rail depth (minimum) . . . . . . . . . . . . . . . . . . . . . . . . . . 864 mm 34''
Top and bottom plate thickness . . . . . . . . . . . . . . . . . 45 mm 1.77''
Side plate thickness . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mm 0.98''
Drive axle mounting . . . . . . . . . . . . . . . .Pin and spherical bushing
Drive axle alignment . . . . . . . . .Swing link between frame and axle
930E-4SE BRAKING SYSTEM
Service brakes: oil-cooled, hydraulic-actuated, multiple disc brakes at
each wheel. Traction system wheel slip/slide control.
Max. service apply pressure . . . . . . . . . . . . . .17237 kPa 2500 psi
Total friction area per brake . . . . . . . . . . . . . . 97025 cm2 15,038 in2
Secondary brakes . . . . . . . . . . . . . . . . .Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
Wheel brake locks . . . . . . . . . . . . . . . . . . . . . . . . .Switch activated
Parking brakes . . . . . . . . . . . . . . . . . .Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade @ maximum gross vehicle weight.
Electric dynamic retarder . . . . . . . . . . . . . . .Max 4026 kW 5400 hp Continuous 2909 kW 3900 hp
Continuously rated high-density blown grids w/retard at engine idle and retard in reverse propulsion.
930E-4SE SUSPENSION
Variable rate hydro-pneumatic with integral rebound control
Max. front stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 328 mm 12.92''
Max. rear stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 mm 9.40''
Max. rear axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6.5°
* Rear suspensions are inverted.
930E-4SE SERVICE CAPACITIES
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . 719 L 190 U.S. gal
Crankcase* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 L 90 U.S. gal
Hydraulic system. . . . . . . . . . . . . . . . . . . . . . . . 1325 L 350 U.S. gal
Motor gear box (each) . . . . . . . . . . . . . . . . . . . . . . 95 L 25 U.S. gal
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5300 L 1400 U.S. gal
* Includes lube oil filters
930E-4SE COOLING SYSTEM
L&M radiator assembly, split-flow, with deareation-type top tank measuring 3277 mm x 2164 10'9'' x 7'1''.
20190103 John - Haulpak Field Engineer
HAULPAK 930E-4SE ENGINE SPECIFICATION
Make and model . . . . . . . . . . . . . . . . . . . . . . Komatsu SSDA18V170
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operating cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 cycle
Gross horsepower . . . . . . . . . . . . . 2611 kW 3,500 HP @ 1900 rpm
Net flywheel power* . . . . . . . . . . . . 2558 kW 3,429 HP @ 1900 rpm
Weight (wet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10100 kg 22,266 lb
* Net flywheel power is the rated power at the engine flywheel minus the average accessory losses. Accessories include fan and charging alternator.
Power ratings above represent engine performance in accordance with SAE J1995 and J1349 conditions.
930E-4SE ELECTRIC DRIVE
AC CURRENT
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GTA-39
Dual impeller in-line blower . . . . . . . . . . . 453 m3 /min 16,000 cfm
Control . . . . . . . . . . . . . . . . . . . . . . . . . AC Torque Control System
Motorized wheels*. . . . . . . GDY106 AC Induction Traction Motors
Ratio** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32.62:1
Speed (maximum) . . . . . . . . . . . . . . . . . . . . . . 64.5 km/h 40 mph
* Wheel motor application depends upon gross vehicle weight, haul road grade, haul road length, rolling resistance and other parameters. Komatsu and G.E. must analyze each job condition to assure proper application.
** Optional ratios available.
930E-4SE TIRES AND RIMS
Rock service, tubeless, radial tires
Standard tire* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53/80 R63 Taper Lock
914 mm x 1600 mm x 127 mm 36'' x 63'' x 5.0'' rim assembly
Rated at 758 kPa 110 psi cold inflation pressure for rims, 600 kPa 87 psi for tires.
* Tires should meet application requirements for tkph/tmph, tread, compound, inflation pressure, ply rating or equivalent, etc.
930E-4SE BODY
All-welded steel flat floor body with horizontal bolsters and full canopy. Eyebrow, rear wheel rock ejectors, body up sling, and rubber mounts on frame are standard. Pivot exhaust heating optional.
Floor sheet . . . . . . . . . . . . . 16 mm 0.63'' 1379 MPa 200,000 psi tensile strength steel (two-piece)
Front sheet . . . . . . . . . . . . . . 9 mm 0.35'' 1379 MPa 200,000 psi tensile strength steel
Side sheet . . . . . . . . . . . . . . 8 mm 0.31'' 1379 MPa 200,000 psi tensile strength steel
Canopy sheet . . . . . . . . . . . . . 5 mm 0.19'' 690 MPa 100,000 psi tensile strength steel
Standard SAE heaped 2:1. . . . . . . . . . . . . . . . . . . 211 m3 276 yd3
Standard Komatsu body weight . . . . . . . . . . . 30362 kg 66,936 lb
* Komatsu must approve all bodies through a Body Application Worksheet.
930E-4SE CAB
Advanced Operator Environment with integral 4-post ROPS/FOPS structure (meets J1040 Apr88), adjustable air suspension seat w/lumbar support and arm rests, passenger seat, maximum R-value insulation, tilt and telescoping steering wheel, electric windshield wipers w/washer, tinted safety glass, power windows, Komatsu Payload Weighing System, 55,000 Btu/hr heater and defroster, 21,600 Btu/hr air conditioning (HFC - 134A refrigerant).
930E-4SE FRAME
Advanced technology, full butt-welded box sectional ladder-type frame with integral ROPS supports, integral front bumper, rear tubular cross members, steel castings at all critical stress transition zones, rugged continuous horsecollar.
Plate material . . . . . . . . . . . . . . . . . . . . . . . . 482.6 MPa 70,000 psi tensile strength steel
Casting material . . . . . . . . . . . . . . . . . . . . . . 620.5 MPa 90,000 psi tensile strength steel
Rail width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 mm 12''
Rail depth (minimum) . . . . . . . . . . . . . . . . . . . . . . . . . . 864 mm 34''
Top and bottom plate thickness . . . . . . . . . . . . . . . . . 45 mm 1.77''
Side plate thickness . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mm 0.98''
Drive axle mounting . . . . . . . . . . . . . . . .Pin and spherical bushing
Drive axle alignment . . . . . . . . .Swing link between frame and axle
930E-4SE BRAKING SYSTEM
Service brakes: oil-cooled, hydraulic-actuated, multiple disc brakes at
each wheel. Traction system wheel slip/slide control.
Max. service apply pressure . . . . . . . . . . . . . .17237 kPa 2500 psi
Total friction area per brake . . . . . . . . . . . . . . 97025 cm2 15,038 in2
Secondary brakes . . . . . . . . . . . . . . . . .Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
Wheel brake locks . . . . . . . . . . . . . . . . . . . . . . . . .Switch activated
Parking brakes . . . . . . . . . . . . . . . . . .Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade @ maximum gross vehicle weight.
Electric dynamic retarder . . . . . . . . . . . . . . .Max 4026 kW 5400 hp Continuous 2909 kW 3900 hp
Continuously rated high-density blown grids w/retard at engine idle and retard in reverse propulsion.
930E-4SE SUSPENSION
Variable rate hydro-pneumatic with integral rebound control
Max. front stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 328 mm 12.92''
Max. rear stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 mm 9.40''
Max. rear axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6.5°
* Rear suspensions are inverted.
930E-4SE SERVICE CAPACITIES
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . 719 L 190 U.S. gal
Crankcase* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 L 90 U.S. gal
Hydraulic system. . . . . . . . . . . . . . . . . . . . . . . . 1325 L 350 U.S. gal
Motor gear box (each) . . . . . . . . . . . . . . . . . . . . . . 95 L 25 U.S. gal
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5300 L 1400 U.S. gal
* Includes lube oil filters
930E-4SE COOLING SYSTEM
L&M radiator assembly, split-flow, with deareation-type top tank measuring 3277 mm x 2164 10'9'' x 7'1''.