1:72 Lockheed Martin F-16D Block 40; aircraft “77 Red” (ex USAF s/n 90-0777) of the 40th Tactical Aviation Brigade, Ukrainian Air Force (Повітряні Сили України, Povitryani Syly Ukrayiny); Vasylkiv Air Base (Kiev Oblast), 2017 (Whif/Kitbashing) - WiP
The kit and its assembly:
I am not a big F-16 fan, but in some cases it’s an unavoidable canvas – just like in this case here. This fictional aircraft model (or better: this model of a [yet] fictional F-16 operator) was spawned by two ideas. One was the simple question: what if the Ukraine had after the USSR’s dissolution chosen a stronger attachment to (old) Western forces after the dissolution of the USSSR? And/or: what if the Ukraine had started to procure non-Russian equipment, esp. aircraft? So, what would an Ukrainian F-16 might have looked like, in general but esp. after the Crimea annexation in 2014 when such a scenario had become even more possible?
The other source of inspiration was a picture of an Ukrainian Su-24 with grey digital camouflage, a scheme that was/is also worn by some Su-25s. When I stumbled upon an Authentic Decals sheet for this unique paint scheme that allows to apply the complex and delicate pattern through water-slide transfers, I thought that the relatively “flat” F-16 surface would be an ideal basis to try this stunt?
What sounded like a very simple livery whif on an OOB model turned into a construction nightmare. Originally, this project provided me with a purpose for a dubious Trumpeter F-16 kit that I had bought some years ago – dead cheap, but righteously so. This kit is cruel, the model even has no concrete variant specification and is apparently the re-boxing of a kit from an obscure Chinese company called “Income”. Effectively, the Trumpeter F-16 is a rip-off of Italeri’s quite nice F-16C/D kit – but the Income/Trumpeter clone comes with MUCH deeper engravings esp. on the fuselage that remind a lot of the dreaded Matchbox “trenches”. Everything is rather “soft” and toylike, the clear parts are poor and the (few) decals look like toy stickers (!!!). I’d call it crude, even the instructions are apparently poor scans or photocopies from the Italeri kit, including hints for detail painting with no corresponding reference what colors should be used at all… All that could have been overlooked, but after starting with the kit I could not commit myself to use it any further. It’s rare that I give up because of a kit’s basis!
Next idea to “save” the project’s idea of an Ukrainian F-16 was to dig out a surplus Intech F-16 from the pile, also bought long ago because it was cheap, as conversion fodder. This kit has also been re-released in infinite variations under the Mister-/Mastercraft label. Upon closer inspection this kit turned out to have massive flaws, too, but in different areas from the Trumpeter thing. For instance, the Intech kit’s wings are utterly thick, certainly 1mm thicker than the Trumpeter model’s parts. This does not sound much, but on the really thin F-16 wings and stabilizers this looks really awful! Furthermore, the clear parts had not been fully molded, so I’d have needed a replacement canopy, anyway. Again, I gave up on building…
…until I decided to make the best of this mess and combine the “best” parts from both gimp models, trying to mend the worst flaws to an acceptable level. This led to the glorious kitbashing that this model eventually became! From the Intech kit I took the acceptable fuselage, including cockpit interior, air intake and landing gear, as well as the fin and the weapon pylons. The Trumpeter kit donated its thinner wings and the stabilizers, as well as the much better open exhaust nozzle (there’s an optional closed one, too; the Intech kit only offers an open nozzle, without ANY surface detail at all, it’s just a blank pipe!).
Beyond these basic ingredients, some more donors became necessary: All clear parts from both Intech and Trumpeter kit turned out to be rubbish for various reasons. The decision to build an F-16D two-seater was dictated by the fact that I had a leftover canopy from an Italeri F-16 kit in the donor bank – luckily it fitted well to the Intech kit’s body. Two crewmen from the spares box populate the cockpit and hide the rather basic interior, which was not improved at all. Furthermore, the ordnance came from external sources, too. The characteristic drop tanks with their cut-off tails were also leftover parts from the Italeri F-16, all AAMs come from a Hasegawa weapon set.
Some PSR was necessary to blend the parts from different kits together – thankfully, almost all F-16 kits are constructed in a similar fashion, even though there are small detail differences. In this case, the wings had to be slightly modified to fit onto the Intech fuselage. However, even those parts from the original kit(s) that are supposed to fit, e.g. the fin or the alternative cockpit opening frames for the optional single- and two-seater canopies, do hardly match at all. Horrible.
I rather focused on the model’s exterior, and a personal addition to improve the overall look of the otherwise rather basic/poor model, I added some small blade antennae that were totally missing on either model. Another extra detail are the small static dischargers on the trailing edges, created with thin, heated sprue material. Only small details, but they improve IMHO the model’s look considerably.
1:72 Lockheed Martin F-16D Block 40; aircraft “77 Red” (ex USAF s/n 90-0777) of the 40th Tactical Aviation Brigade, Ukrainian Air Force (Повітряні Сили України, Povitryani Syly Ukrayiny); Vasylkiv Air Base (Kiev Oblast), 2017 (Whif/Kitbashing) - WiP
The kit and its assembly:
I am not a big F-16 fan, but in some cases it’s an unavoidable canvas – just like in this case here. This fictional aircraft model (or better: this model of a [yet] fictional F-16 operator) was spawned by two ideas. One was the simple question: what if the Ukraine had after the USSR’s dissolution chosen a stronger attachment to (old) Western forces after the dissolution of the USSSR? And/or: what if the Ukraine had started to procure non-Russian equipment, esp. aircraft? So, what would an Ukrainian F-16 might have looked like, in general but esp. after the Crimea annexation in 2014 when such a scenario had become even more possible?
The other source of inspiration was a picture of an Ukrainian Su-24 with grey digital camouflage, a scheme that was/is also worn by some Su-25s. When I stumbled upon an Authentic Decals sheet for this unique paint scheme that allows to apply the complex and delicate pattern through water-slide transfers, I thought that the relatively “flat” F-16 surface would be an ideal basis to try this stunt?
What sounded like a very simple livery whif on an OOB model turned into a construction nightmare. Originally, this project provided me with a purpose for a dubious Trumpeter F-16 kit that I had bought some years ago – dead cheap, but righteously so. This kit is cruel, the model even has no concrete variant specification and is apparently the re-boxing of a kit from an obscure Chinese company called “Income”. Effectively, the Trumpeter F-16 is a rip-off of Italeri’s quite nice F-16C/D kit – but the Income/Trumpeter clone comes with MUCH deeper engravings esp. on the fuselage that remind a lot of the dreaded Matchbox “trenches”. Everything is rather “soft” and toylike, the clear parts are poor and the (few) decals look like toy stickers (!!!). I’d call it crude, even the instructions are apparently poor scans or photocopies from the Italeri kit, including hints for detail painting with no corresponding reference what colors should be used at all… All that could have been overlooked, but after starting with the kit I could not commit myself to use it any further. It’s rare that I give up because of a kit’s basis!
Next idea to “save” the project’s idea of an Ukrainian F-16 was to dig out a surplus Intech F-16 from the pile, also bought long ago because it was cheap, as conversion fodder. This kit has also been re-released in infinite variations under the Mister-/Mastercraft label. Upon closer inspection this kit turned out to have massive flaws, too, but in different areas from the Trumpeter thing. For instance, the Intech kit’s wings are utterly thick, certainly 1mm thicker than the Trumpeter model’s parts. This does not sound much, but on the really thin F-16 wings and stabilizers this looks really awful! Furthermore, the clear parts had not been fully molded, so I’d have needed a replacement canopy, anyway. Again, I gave up on building…
…until I decided to make the best of this mess and combine the “best” parts from both gimp models, trying to mend the worst flaws to an acceptable level. This led to the glorious kitbashing that this model eventually became! From the Intech kit I took the acceptable fuselage, including cockpit interior, air intake and landing gear, as well as the fin and the weapon pylons. The Trumpeter kit donated its thinner wings and the stabilizers, as well as the much better open exhaust nozzle (there’s an optional closed one, too; the Intech kit only offers an open nozzle, without ANY surface detail at all, it’s just a blank pipe!).
Beyond these basic ingredients, some more donors became necessary: All clear parts from both Intech and Trumpeter kit turned out to be rubbish for various reasons. The decision to build an F-16D two-seater was dictated by the fact that I had a leftover canopy from an Italeri F-16 kit in the donor bank – luckily it fitted well to the Intech kit’s body. Two crewmen from the spares box populate the cockpit and hide the rather basic interior, which was not improved at all. Furthermore, the ordnance came from external sources, too. The characteristic drop tanks with their cut-off tails were also leftover parts from the Italeri F-16, all AAMs come from a Hasegawa weapon set.
Some PSR was necessary to blend the parts from different kits together – thankfully, almost all F-16 kits are constructed in a similar fashion, even though there are small detail differences. In this case, the wings had to be slightly modified to fit onto the Intech fuselage. However, even those parts from the original kit(s) that are supposed to fit, e.g. the fin or the alternative cockpit opening frames for the optional single- and two-seater canopies, do hardly match at all. Horrible.
I rather focused on the model’s exterior, and a personal addition to improve the overall look of the otherwise rather basic/poor model, I added some small blade antennae that were totally missing on either model. Another extra detail are the small static dischargers on the trailing edges, created with thin, heated sprue material. Only small details, but they improve IMHO the model’s look considerably.