1:72 Focke Wulf Ta 152J-2; “Weisse Zwölf” (12+~ White) of the 10./JG26 der Deutschen Luftwaffe, piloted by Hauptmann Wernher Suhrbier; Flensburg, early 1946 (modified Mistercraft Fw 190 kit) - WiP
The kit and its assembly:
This is a what-if model, but, as usual, it is rooted in reality – to be precise in the German late-war plans to mate the Ta 152(H) with the mighty Jumo 222 engine. I do not know what the official service designation would have been, but this combo would have resulted in a powerful fighter – AFAIK, German engineers’ calculations indicated a performance that would have been comparable with the post-WWII F4U-5!
Creating a model of such this paper aircraft called for some serious conversion work and ended almost in a kitbashing. The starting point became a (cheap) Mistercraft Fw 190D-9 kit, and I originally planned this model to be a Fw 190 variant, but eventually this turned into a Ta 152, since it would better match up with the late war time frame.
The Mastercraft/Mistercraft kit appears to be an indigenous mold and not a re-issue of a vintage kit. At first glance the parts look pretty crisp, but the kit has some serious fit and flash issues. Another selling point is the detailed decal set, which comes in three sheets and encompasses a lot of stencils – even though the instructions where to place them are not consistent, and there are even 1:48 scale(!) markings included. But that’s a Mastercraft/Mistercraft standard, anyway…
Well, the basis was sound and the kit would, in any event, be thoroughly modified. From the OOB kit, fuselage, wings and stabilizers were taken, as well as the landing gear and some other bits.
The wings were extended, in order to keep overall proportions with the new, much more massive engine cowling balanced (see below). Not an easy stunt, but I was lucky to have recently bought a set of resin Doppelreiter tanks from Airmodel which were just perfect to cover the cuts and seams on the upper wing surfaces. Inside of the wings, a styrene strip secured stability while the lower wing surface was sculpted with putty and the trailing edge of the outer wing panels was cut down by 1 mm, so that the wings’ outlines match again. Some further PSR work was necessary to blend the slipper tanks into the wings, forming the upper side of the modifications, but in the end the whole thing looks quite good.
The fuselage lost both its original engine and the tail. The latter is a donor part from a Frog Ta 152H (Revell re-boxing), but mating it with the Mistercraft Fw 190D was not easy because the fuselage shapes of the two kits are totally different! I also used the Mistercraft stabilizers because they were markedly bigger than the same parts from the Ta 152 kit!
The Jumo 222 front end was simulated with parts from the spares box, and it is a bit exaggerated. Actually, the Jumo 222 was hardly bigger (in both length and diameter) than the Fw 190D’s Jumo 213 V12 engine! The cowling and the radiator for my conversion came from a Frog He 219 engine nacelle (Revell re-boxing, too) which is utterly dubious. The nacelle parts were turned upside down and integrated into the slender Fw 190 front fuselage with several layers of putty.
Inside of the cowling, a radiator plate from an Italeri Fw 190D was mounted, together with a styrene tube adapter for the new propeller. The latter was scratched, using a drop tank as spinner and single propeller blades from the Mistercraft Fw 190D, plus one donor blade from the Frog Ta 152H kit, which had to be trimmed in order to match the other blades. But with some paint, no one will tell the small differences…
Once the bigger engine was integrated into the fuselage, the exhaust system had to be added. In real life, the Jumo 222 would have featured three clusters with two rows of four exhaust stubs, distributed evenly around the cowling. Using a drawing of this arrangement as benchmark, I started with square cuts for the cluster openings. From the back side, styrene sheet closed the gaps and offered a basis for the exhaust stubs. These were improvised with H0 scale roofing shingles – each of the 24 exhaust stubs was cut individually into shape and size and then glued into the respective openings on the upper flanks and under the engine. Finally, styrene sheet was used to create small spoilers and heat shields. The result is certainly not perfect, but comes close to what the real world arrangement would basically have looked like. In a final step, two air intakes for the two-stage supercharger, scratched from sprue material, were added to the flanks.
The cockpit remained OOB, simple as it is, as well as the landing gear, but the canopy was modified in order to allow a presentation in open position. This meant that the OOB canopy had to be cut in two parts and that the model’s spine had to be cut away, making place for a donor canopy (the late, bulged variant, IIRC from an Italeri Fw 190D-9). Internally the fuselage gap was filled with putty and the headrest had to be modified, too, but the conversion turned out to look better than expected.
As a small cosmetic improvement, the molded gun barrel stumps in the wing roots were replaced with hollow steel needles, and the outer guns were completely removed.
1:72 Focke Wulf Ta 152J-2; “Weisse Zwölf” (12+~ White) of the 10./JG26 der Deutschen Luftwaffe, piloted by Hauptmann Wernher Suhrbier; Flensburg, early 1946 (modified Mistercraft Fw 190 kit) - WiP
The kit and its assembly:
This is a what-if model, but, as usual, it is rooted in reality – to be precise in the German late-war plans to mate the Ta 152(H) with the mighty Jumo 222 engine. I do not know what the official service designation would have been, but this combo would have resulted in a powerful fighter – AFAIK, German engineers’ calculations indicated a performance that would have been comparable with the post-WWII F4U-5!
Creating a model of such this paper aircraft called for some serious conversion work and ended almost in a kitbashing. The starting point became a (cheap) Mistercraft Fw 190D-9 kit, and I originally planned this model to be a Fw 190 variant, but eventually this turned into a Ta 152, since it would better match up with the late war time frame.
The Mastercraft/Mistercraft kit appears to be an indigenous mold and not a re-issue of a vintage kit. At first glance the parts look pretty crisp, but the kit has some serious fit and flash issues. Another selling point is the detailed decal set, which comes in three sheets and encompasses a lot of stencils – even though the instructions where to place them are not consistent, and there are even 1:48 scale(!) markings included. But that’s a Mastercraft/Mistercraft standard, anyway…
Well, the basis was sound and the kit would, in any event, be thoroughly modified. From the OOB kit, fuselage, wings and stabilizers were taken, as well as the landing gear and some other bits.
The wings were extended, in order to keep overall proportions with the new, much more massive engine cowling balanced (see below). Not an easy stunt, but I was lucky to have recently bought a set of resin Doppelreiter tanks from Airmodel which were just perfect to cover the cuts and seams on the upper wing surfaces. Inside of the wings, a styrene strip secured stability while the lower wing surface was sculpted with putty and the trailing edge of the outer wing panels was cut down by 1 mm, so that the wings’ outlines match again. Some further PSR work was necessary to blend the slipper tanks into the wings, forming the upper side of the modifications, but in the end the whole thing looks quite good.
The fuselage lost both its original engine and the tail. The latter is a donor part from a Frog Ta 152H (Revell re-boxing), but mating it with the Mistercraft Fw 190D was not easy because the fuselage shapes of the two kits are totally different! I also used the Mistercraft stabilizers because they were markedly bigger than the same parts from the Ta 152 kit!
The Jumo 222 front end was simulated with parts from the spares box, and it is a bit exaggerated. Actually, the Jumo 222 was hardly bigger (in both length and diameter) than the Fw 190D’s Jumo 213 V12 engine! The cowling and the radiator for my conversion came from a Frog He 219 engine nacelle (Revell re-boxing, too) which is utterly dubious. The nacelle parts were turned upside down and integrated into the slender Fw 190 front fuselage with several layers of putty.
Inside of the cowling, a radiator plate from an Italeri Fw 190D was mounted, together with a styrene tube adapter for the new propeller. The latter was scratched, using a drop tank as spinner and single propeller blades from the Mistercraft Fw 190D, plus one donor blade from the Frog Ta 152H kit, which had to be trimmed in order to match the other blades. But with some paint, no one will tell the small differences…
Once the bigger engine was integrated into the fuselage, the exhaust system had to be added. In real life, the Jumo 222 would have featured three clusters with two rows of four exhaust stubs, distributed evenly around the cowling. Using a drawing of this arrangement as benchmark, I started with square cuts for the cluster openings. From the back side, styrene sheet closed the gaps and offered a basis for the exhaust stubs. These were improvised with H0 scale roofing shingles – each of the 24 exhaust stubs was cut individually into shape and size and then glued into the respective openings on the upper flanks and under the engine. Finally, styrene sheet was used to create small spoilers and heat shields. The result is certainly not perfect, but comes close to what the real world arrangement would basically have looked like. In a final step, two air intakes for the two-stage supercharger, scratched from sprue material, were added to the flanks.
The cockpit remained OOB, simple as it is, as well as the landing gear, but the canopy was modified in order to allow a presentation in open position. This meant that the OOB canopy had to be cut in two parts and that the model’s spine had to be cut away, making place for a donor canopy (the late, bulged variant, IIRC from an Italeri Fw 190D-9). Internally the fuselage gap was filled with putty and the headrest had to be modified, too, but the conversion turned out to look better than expected.
As a small cosmetic improvement, the molded gun barrel stumps in the wing roots were replaced with hollow steel needles, and the outer guns were completely removed.