1:72 Suchoj-Chizhevskiy SuCh-1 (Suchoj I-2M107), aircraft '23 White' of 176th GvIAP, 302nd IAD, 16th VA, USSR Air Force; Byelorussian front, early 1945

DISCLAIMER

Nothing you see here is real, even though the conversion or the presented background story might be based historical facts. BEWARE!

.

 

Some background:

The mighty Suchoj SuCh-1 started its life in early March 1943, when the Sukhoi OKB finished work on the design of a high-speed fighter with a unique powerplant arrangement. The aircraft was an all-metal low-wing mono­plane with conventional tail surfaces. The three-section wings had constant dihedral and basically trapezoidal planform; the sta­bilizers had zero dihedral.

 

Two Klimov M-107 water-cooled Vee-12 engines, each with a. take-off power of 1 ,600 hp (1,193 kW) and a maximum design power of 1,500 hp (1,119 kW) at 5,500 m (18,045 ft), were mounted in the center fuse­lage in a staggered-tandem arrangement: the front engine was offset to starboard and of the rear one to port. Thus, the total power was increased but the drag was the same as for a single-engined aircraft, which was expected to increase fight speed consider­ably. Consequently, the project was internally designated 'I-2M107', literally "Article powered by two M107 engines".

 

Furthermore, the left cylinder bank of the front engine and the right cylinder bank of the rear engine were disposed vertically, so that each engine had one set of exhaust stubs on top of the fuselage and one on the fuselage side. Both engines drove a single three ­blade tractor propeller of 4.0 m (13 tt 2 in) diameter via parallel extension shafts and a common reduction gearbox. Both water radiators were located side by side in a chin housing, while the oil coolers were buried in the wings. The total fuel capacity of the four tanks arranged in the center fuselage was 1,113 litres (244.86 Imp. gal).

 

Because of the power plant arrangement and the large ground angle (necessary to give adequate ground clearance for the large propeller) the cockpit was offset to port and placed ahead of the wing leading edge to provide better forward visibility on take-off and landing. The cockpit was protected by a bulletproof windscreen, a front armor plate and an armored backrest; the armor weight totaled 70kg (154Ib).

 

The main landing gear units with 800 x 280 mm (31.5x11 in) wheels retracted inwards into the wing roots and the 400 x 150 mm (15.7 x 5.9 in) tail wheel retracted aft. The fighter's armament consisted of two wing-mounted 12.7-mm Berezin UBS machine-guns firing outside the propeller disc and a single 20-mm ShVAK cannon fir­ing through the propeller hub*.

 

A full-scale mock-up was inspected in December 1943, and with German long range bombers threatening the Western front line as well as the lack of a fast and powerful fighters to intercept them (the earlier MiG-5 had turned out to be a disappointment, and Mikoyan's I-211/221 family if high altitude fighters also suffered from serious technical problems at that time), OKB Suchoj received an immediate go-ahead for further development of the SuCh-1, how the I-2M107 was now officially called, since Vladimir A. Chizhevskiy took lead of the project.

 

In the course of 1944 three prototypes went through a fast development program. While the aircraft itself was easy to handle, overheating problems and trouble with the gearbox for the two engines could only partly be rectified - esp. the power transmission should remain the SuCh-1s Achilles Heel.

 

Anyway, the Su-5 was ready for service introduction towards late 1944, and the powerful type was exclusively to be used as an interceptor. Several improvements had been made, compared to the prototypes: now two slightly more powerful Klimov VK-107A engines were used, which were better suited for high altitude operations, and the chin-mounted water cooler was considerably enlarged. The oil coolers had been re-designed and they were now placed under the wing roots.

 

The wing span had been extended by 6' and a bigger (now 4.3m diameter!), four-bladed propeller was added in order to improve performance at high altitude. No pressurized cabin was installed, but the cockpit received an extended glazing for better all-round field of vision.

 

Armament had also been augmented: now a Nudelman N-23 23mm cannon was firing through the propeller hub, and the number of UBS machine-guns in the wings was increased to four.

 

As initial duty experience was gathered, it became quickly clear that the firepower had to be augmented, so that the propeller-hub-mounted 23mm cannon was quickly replaced by a Nudelman-Richter NR-37 37mm cannon, and the four wing-mounted UBS machine guns were replaced by two 20-mm ShVAK cannons or even two Nudelman N-23 23mm cannons - the latter became the production standard from March 1945 on, even though the type's designation did not change.

 

Experience also showed that the overheating problem had been cured, but the complicated gear box tended to malfunction, esp. when full power was called for in aerial combat: high G forces took their toll and damaged the bearings, even warping the extension shafts and structural parts, so that some SuCh-1 were literally torn apart in mid-air.

 

The high torque powers of the large propeller also took their toll on handling: starting and landing was described as "hazardous", esp. when the fuel tanks were empty or in cross winds.

Consequently, SuCh-1 pilots were warned to engage into any dogfight or enter close combat with single-engined enemy fighters, and just focus on large enemy aircraft.

 

On the other side, the SuCh-1's powerful cannon armament made it a deadly foe: a single hit with the NR-37 cannon could down an aircraft, and its top speed of roundabout 700 km/h (435 mph) was more than enough for the Luftwaffe's heavy bomber types like the He 177.

 

Several engine and armament experiments were undertaken. For instance, at least one SuCh-1 was outfitted with a Nudelman-Sooranov NS-45 45mm cannon firing through the propeller hub, even a 57mm cannon was envisaged. Furthermore, one airframe was prepared to carry two Charomskiy M-30V 12 cylinder diesel engines, in order to produce a heavy long-range escort fighter (internally called I-2M30V).

In order to minimize the torque problems a contraprop arrangement with two three-bladed propellers and a diameter of only 3.6m was under development.

 

All in all only 120 of these powerful machines were built until the end of hostilities, as the feared mass attacks of German long range bombers did not materialize. as the Su-7 was complicated to operate and jet engines promised a far more efficient way of propulsion for high speeds, the type was already retired in 1947 and replaced by 1st generation jet fighters like the Yak-15 and MiG-9, which carried a similar armament, attained a better performance (except for the range) but weighed only half of the large and heavy SuCh-1.

.

 

General characteristics

Crew: One

Length: 11.75 m (38 ft 5 3/4 in)

Wingspan: 13.85 m (45 ft 3 1/4 in)

Height: 5.30 m (17 ft 4 in)

Empty weight: 5.250 kg (11.565 lb)

Max. take-off weight: 8.100 kg (17.840 lb)

 

Powerplant:

2× Klimov VK-107A liquid-cooled V12 engines with an output of 1.650 hp (1.210 kW) each at sea level and 900 hp (650 kW) at 8.300m (27.220 ft)

 

Performance:

Maximum speed: 720 km/h (447 mph) at height, clean configuration

Range: 750 km (465 mi)

Service ceiling: 11.700 m (38.400 ft)

Rate of climb: 876 m/mim (2.850 ft/min)

 

Armament:

1× Nudelman-Richter NR-37 37mm cannon with 60 RPG, firing through the propeller hub

2× Nudelman N-23 23mm cannons with 120 RPG in the wings

Many different cannon and machine gun arrangements coulod be found, though.

 

*Information about the conceptual Suchoj I-2M107 was primarily gathered from the book 'OKB Suchoj', written by Yefim Gordon & Dmitriy Komissarov; Hersham (UK), 2010.

.

 

The kit and its assembly (a long story!):

This abomination of an aircraft is/was real, even though the I-2M107 was never built – the fictional name Suchoj-Chizhevskiy SuCh-1 was actually chosen because I could not find any plausible Su-X code for a WWII fighter. Vladimir A. Chizhevskiy actually joined the Suchoj OKB in mid WWII, so I deemed this alternative to be plausible.

 

I had this on the agenda for a long time, but the horrors of kitbashing kept me from building it - until now. The current Anthony P memorial Group Build (for the deceased fellow member at whatifmodelers.com, RIP) was a good motivation to tackle this brute thing. Fortunately, I already had some major ingredients in store, so work could start asap.

 

From that, anything else was improvised from the scrap box, and with only a three side view of the I-2M107 as guidance. It became a true Frankenstein creation with...

 

● Fuselage and inner wings from the (horrible) NOVO Attacker

● Wings from an Italeri Fw 190 D-9 attached to them

● Nose is a resin Griffon from an Avro Lincoln conversion set from OzMods

● Tail cone is a radar nose from an F-4J Phantom II

● Tail fin is a horizontal stabilizer from a Matchbox SB2C Helldiver

● Vertical stabilizers come from a Matchbox Me 410

● Oil coolers are modified front landing gear wells from two Revell G.91 kits

● Cockpit hood comes from a Revell P-39 Airacobra

● Landing gear comes from an Italeri Fw 190 D-9, covers were modified/improvised

● Main wheels belong to a MPM Ryan Dark Shark

● Tail wheel belongs to a Matchbox Harrier

● The propeller was scratched, IIRC from a Grumman Hellcat drop tank front and blades from an Airfix A-1 Skyraider. Inside, a metal axis was mounted.

.

 

Work started with the fuselage and the wings as separate segments.

 

The Attacker fuselage lost its fin and the cockpit and air intakes were simply cut away, just as the tail pipe. The resin Griffon was slightly shortened at the front, but more or less directly attached to the fuselage, after I had cut out openings for the four rows of exhaust nozzles.

Then, the new tail cone was glued onto the end and the original fairings for the Attacker's stabilizer cut away and sanded even - anything had to be made new.

 

The wings were a bit tricky. I had hoped to use the Attacker's OOB wings, but these were not only much too small and did not have the proper shape, they also lacked landing gear wells!

 

Finding a solution was not easy, and I had to improvise. After some trials I decided to cut the Attacker wing span at about the width where the guns are located, and then add Fw 190 wings.

The depth would be fine, even though the Fw 190 wings were a bit thicker, and they offered a leading edge kink which was good for the original and characteristic I-2M107's wing root extensions. The latter were sculpted from a 6mm thick core or styrene sheet, added to the Attacker parts' leading edge, and the rest, as well as the lacking Attacker wing's thickness, sculpted with 2C and later NC putty.

 

Furthermore I cut out and sculpted landing gear wells, another challenging, since these had to cover the Attacker/Fw 190 parts' intersection! LOTS of putty work, sanding and shaving, but as a benefit I was able to use the Attacker kit's original wing/fuselage joints. Effectively, my placement turned out to be a bit far outside, so the track appears too wide - the price to pay when you work on single parts. Anyway, I left it was it turned out, as a major correction at a late working stage would mean to tear anything apart again...

 

Back to the nose: adding the propeller and the cockpit into the massive nose was the next working station. The propeller had to be huge, and also needed a rather big spinner. A contraprop was ruled out, even though it would have looked great here. But eventually I settled for a scratch-built thing, made from a teardrop-shaped drop tank front onto which the four blades from a A-1 Skyraider were glued. Probably the biggest prop I have ever put onto a 1:72 scale model! Since the resin nose was massive, drilling a hole and adding a metal axis to the propeller was enough.

 

With that in place I started carving out a cockpit opening - it worked better and easier than expected with a mini drill and a coarse shaving head! The opening is still rather small, a seat and a pilot hardly fit, but it works - I found a rather smallish pilot figure, and added a seat and some other small details from the scrap box, just to have something inside.

 

For a canopy I found a very old (30 years, I guess...) clear part from a Revell P-39 Airacobra in the scrap box, which was almost perfect in shape and width. It was a bit blind and stained with ancient enamel paint, but some wet sanding and serious polishing almost got it back to translucent status. Since I would not open the cockpit, this was a sufficient solution.

 

The asymmetrical cockpit opening was, in an initial step, faired with styrene strips, for a rough outline, and then sculpted with 2C and later NC putty, blending it into the rest of the fuselage.

 

For the tail surfaces, the SB2C stabilizer was cut away at its base - it is not a bad donation piece, its shape and rudder come pretty close to the I-2M107's original design!

The stabilizers I used on my kitbash come from a Me 410, and their leading edge was a cut away so that the sweep angle would be a bit larger. They lack depth, compared to the I-2M107's original design, but since the wings have become more slender, too, I think it's a good compromise, and the best what I had at hand in the spares stash.

 

Finally, and before detail work could start, the wings were attached to the fuselage. I eventually set them back by ~6mm, so that the new, extended leading edge would match the respective fairing on the fuselage. The resulting gap at the trailing edge was, again, filled with 2C and NC putty.

 

A personal change was a different oil cooler arrangement. The original location was to be in the wings' leading edge, just in front of the landing gear wells - but that appeared a bit doubtful, as I could not find a plausible solution where the exit for the air would be? Consequently, and in order to avoid even more messy putty sculpting on the wings, I decided to re-locate the oil coolers completely, into shallow, tunnel-like fairings under the wing roots, not unlike the radiator arrangement on a Spitfire or Bf 109.

 

In order to check the surface quality I decided to add a coat of grey primer, once the fuselage/wing segments had been connected. This showed only minor flaws, but made another turn with NC putty and wet sanding necessary.

 

Now it was time for finishing touches, e .g. mounting the landing gear, completing the cockpit and adding exhaust stubs - cut individually from HO scale model railroad roof tiles and inserted into the four fuselage fairings.

 

The canopy was fixed into place with white glue, which also helped closing some small gaps.

.

 

Painting and markings:

While the I-2M107 looks odd, to say the least, I wanted to keep the paint scheme rather simple and quasi-authentic. I went for a pale grey/green camouflage, used e. g. on late war Yakovlev Yak-3 fighters.

 

Basic colors are Humbrol 31 (Slate Grey, it has a very greenish, even teal, hue), ModelMaster 1740 (Dark Gull Grey, FS 36231) and Humbrol 167 (Barley Grey) for the lower sides with a wavy waterline. Since only marginal surface details were left over, I decided to fake panels and panel lines with paint.

Panels were simulated with lighter shades of the basic tones (RLM 62 from ModelMaster, Humbrol 140 and 127 below), panel lines were painted with highly thinned grey acrylic paint and a special brush - in German it's called a 'Schlepppinsel', it's got very long hairs and is also used to paint scallops on car models, and similar things are used for real car tuning/custom paintwork, too.

Sure, the painted panel lines are a bit rough, but I did not want to risk any damage through manual engraving on the rather delicate mixed-media surface of the kitbashed model. For an overall look or first impression it's very good, though.

 

As 'highlights' I added a white spinner and half of the fin was painted white, too.

 

The decals were puzzled together. The flashes and the tactical code number come from a Hobby Boss La-7, the Red Stars, IIRC, belong to a vintage MiG-21F from Hasegawa. The "Rodinu" slogan actually belongs to a 1:35 Soviet Tank decals set.

 

Finally, after some additional dry painting with light grey, some oil stains around the engines and coolers and soot stains at the exhaust stubs and guns (painted, plus some grinded graphite, as it yields a nice, metallic shimmer that looks like oil or burnt metal), everything was sealed under a coat of matt acrylic varnish.

 

 

If it had been built, the Suchoj I-2M107 must have been an impressive aircraft - it was bigger than a P-47 Thunderbolt or an A-1 Skyraider, and one can only wonder how its field performance would have been?

Similar concepts had been underway in UK, too, e. g. for a heavy naval attack aircraft, but the I-2M107 with its asymmetrical cockpit and engine arrangement were unique. A worthy whif, even if some details like the landing gear or the borrowed nose section are not 100% 'correct'.

 

Done