USB WiFi Ralink RT2870F Chip

photo by Arkadiusz Sikorski © 2012 / www.arq.pl/ | www.sikorski.art.pl/

 

 

Wiphy phy1

Band 1:

Capabilities: 0x2f2

HT20/HT40

Static SM Power Save

RX Greenfield

RX HT20 SGI

RX HT40 SGI

TX STBC

RX STBC 2-streams

Max AMSDU length: 3839 bytes

No DSSS/CCK HT40

Maximum RX AMPDU length 65535 bytes (exponent: 0x003)

Minimum RX AMPDU time spacing: 2 usec (0x04)

HT RX MCS rate indexes supported: 0-15, 32

TX unequal modulation not supported

HT TX Max spatial streams: 2

HT TX MCS rate indexes supported may differ

Frequencies:

* 2412 MHz [1] (20.0 dBm)

* 2417 MHz [2] (20.0 dBm)

* 2422 MHz [3] (20.0 dBm)

* 2427 MHz [4] (20.0 dBm)

* 2432 MHz [5] (20.0 dBm)

* 2437 MHz [6] (20.0 dBm)

* 2442 MHz [7] (20.0 dBm)

* 2447 MHz [8] (20.0 dBm)

* 2452 MHz [9] (20.0 dBm)

* 2457 MHz [10] (20.0 dBm)

* 2462 MHz [11] (20.0 dBm)

* 2467 MHz [12] (20.0 dBm)

* 2472 MHz [13] (20.0 dBm)

* 2484 MHz [14] (20.0 dBm)

Bitrates (non-HT):

* 1.0 Mbps

* 2.0 Mbps (short preamble supported)

* 5.5 Mbps (short preamble supported)

* 11.0 Mbps (short preamble supported)

* 6.0 Mbps

* 9.0 Mbps

* 12.0 Mbps

* 18.0 Mbps

* 24.0 Mbps

* 36.0 Mbps

* 48.0 Mbps

* 54.0 Mbps

max # scan SSIDs: 4

max scan IEs length: 2257 bytes

Coverage class: 0 (up to 0m)

Supported Ciphers:

* WEP40 (00-0f-ac:1)

* WEP104 (00-0f-ac:5)

* TKIP (00-0f-ac:2)

* CCMP (00-0f-ac:4)

Available Antennas: TX 0 RX 0

Supported interface modes:

* IBSS

* managed

* AP

* AP/VLAN

* WDS

* monitor

* mesh point

software interface modes (can always be added):

* AP/VLAN

* monitor

valid interface combinations:

* #{ AP, mesh point } <= 8,

total <= 8, #channels <= 1

Supported commands:

* new_interface

* set_interface

* new_key

* new_beacon

* new_station

* new_mpath

* set_mesh_params

* set_bss

* authenticate

* associate

* deauthenticate

* disassociate

* join_ibss

* join_mesh

* set_tx_bitrate_mask

* action

* frame_wait_cancel

* set_wiphy_netns

* set_channel

* set_wds_peer

* Unknown command (84)

* Unknown command (87)

* Unknown command (85)

* Unknown command (89)

* Unknown command (92)

* connect

* disconnect

Supported TX frame types:

* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

* Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

Supported RX frame types:

* IBSS: 0x40 0xb0 0xc0 0xd0

* managed: 0x40 0xd0

* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0

* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0

* mesh point: 0xb0 0xc0 0xd0

* P2P-client: 0x40 0xd0

* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0

* Unknown mode (10): 0x40 0xd0

Device supports RSN-IBSS.

HT Capability overrides:

* MCS: ff ff ff ff ff ff ff ff ff ff

* maximum A-MSDU length

* supported channel width

* short GI for 40 MHz

* max A-MPDU length exponent

* min MPDU start spacing

Device supports TX status socket option.

Device supports HT-IBSS.

Done