1:72 Nanchang Qiangjiji-6/A-6B 'Kong Yun' (NATO: 'Fruitcase B'); (Whif/Kitbashing) - WiP
The kit and its assembly:
This is a whif, but the Nanchang Q-6 was actually developed until 1989 – even though it never entered any service. It was over-ambitious and a dead end, overtaken by technological advances and the fact that Chinese development used to take decades rather than years.
Anyway, the Q-6 actually looked as if someone had glued the nose and air intake of a F-16 onto a MiG-23/27 fuselage - weird, but cool, so why not try this at home?
Like many kitbashing things, what sounds simple turned out to be a bit tricky in detail, even though the surgery was finally easier than expected. The model basis is pretty simple: I took an Academy MiG-27, sawed off the fuselage in the wing roots area (about 1cm, the cockpit section is an extra fuselage section), and did the same with an Italeri F-16 nose section, right behind the cockpit, where the front wheel well ends. The top insert for the single seater was left a bit longer, so that it would overlap with the MiG-23/27 spine.
When you fit these parts together, height is almost perfect, even the wing root/LERX angles match, but there are gaps left on the flanks where the original MiG-27 air intakes would be. These have to be covered, what creates lines reminiscent of the respective area on a MRCA Tornado. Furthermore, the spine behind the cockpit has to be sculpted, too.
Furthermore, the wing root levels of the MiG-23/27 and the F-16 did not match - they have a difference in height of about 4mm on the model, and this was the biggest challenge.
In order to compensate for this problem on my model, any LERX sign was removed from the F-16 nose. Inside of the F-16 section, a column was added that supports the rear upper half of the front fuselage, since the flanks had to go almost completely.
On the outside, the necessary intersections/extensions sculpted new with 2C putty, extending the MiG-23/27 lines forward. The final surface finish was done with NC putty. This major surgery was less complicated than expected - lots of work, though, but feasible.
The new front section with its blended fuselage/LERX area around the cockpit reminds surprisingly much of the MiG-29? As a side note: when you look at CG simulations of this aircraft, this area is a frequent field of trial and error. You find unconclusive, if not impossible designs.
Other changes include a less modern canopy from a MiG-21 (I think it comes from an Academy MiG-21F kit), which was more tricky to fit onto the original F-16 canopy than the LERX stuff. The F-16 canopy looked just too modern for my taste. An old Airfix pilot figure was added, too.
Another new feature is a new jet pipe, a J-79 nozzle from an Italeri Kfir that fits perfectly into the rear fuselage, and the fin. The latter was taken as a leftover part from my recent CF-151A project and comes from a 1:144 scale Tu-22M bomber (Dragon). It's higher, but less deep, and I thought that a slightly different shape and more area would be suitable for an attack aircraft. For the same reason the single, foldable stabilizer fin under the rear fuselage was replaced by two fixed strakes (from the F-16). Small details, but they change the look and make the aircraft appear more simple.
The landing gear was taken from the MiG-27, the front wheel strut had to be slightly shortened due to the reduced wheelbase on the Q-6.
The ordnance was puzzled together – according to current BAF weapons in use. I went for unguided missiles (taken from the Academy MiG-27 donation kit) and some 100kg iron bombs, leftover from a Trumpeter Il-28 bomber kit. These were arranged under the wing roots on improvised tandem MERs.
I did not even try to engrave new panel lines on the new front section - actually, almost the whole upper surface is featureless since it was made with putty. But bot 2C and NC putty are pretty touchy to drilling or engraving (as the rather fruitless attempt to drill open cavities for the two guns proved...), so I decided to just use paint effects.
1:72 Nanchang Qiangjiji-6/A-6B 'Kong Yun' (NATO: 'Fruitcase B'); (Whif/Kitbashing) - WiP
The kit and its assembly:
This is a whif, but the Nanchang Q-6 was actually developed until 1989 – even though it never entered any service. It was over-ambitious and a dead end, overtaken by technological advances and the fact that Chinese development used to take decades rather than years.
Anyway, the Q-6 actually looked as if someone had glued the nose and air intake of a F-16 onto a MiG-23/27 fuselage - weird, but cool, so why not try this at home?
Like many kitbashing things, what sounds simple turned out to be a bit tricky in detail, even though the surgery was finally easier than expected. The model basis is pretty simple: I took an Academy MiG-27, sawed off the fuselage in the wing roots area (about 1cm, the cockpit section is an extra fuselage section), and did the same with an Italeri F-16 nose section, right behind the cockpit, where the front wheel well ends. The top insert for the single seater was left a bit longer, so that it would overlap with the MiG-23/27 spine.
When you fit these parts together, height is almost perfect, even the wing root/LERX angles match, but there are gaps left on the flanks where the original MiG-27 air intakes would be. These have to be covered, what creates lines reminiscent of the respective area on a MRCA Tornado. Furthermore, the spine behind the cockpit has to be sculpted, too.
Furthermore, the wing root levels of the MiG-23/27 and the F-16 did not match - they have a difference in height of about 4mm on the model, and this was the biggest challenge.
In order to compensate for this problem on my model, any LERX sign was removed from the F-16 nose. Inside of the F-16 section, a column was added that supports the rear upper half of the front fuselage, since the flanks had to go almost completely.
On the outside, the necessary intersections/extensions sculpted new with 2C putty, extending the MiG-23/27 lines forward. The final surface finish was done with NC putty. This major surgery was less complicated than expected - lots of work, though, but feasible.
The new front section with its blended fuselage/LERX area around the cockpit reminds surprisingly much of the MiG-29? As a side note: when you look at CG simulations of this aircraft, this area is a frequent field of trial and error. You find unconclusive, if not impossible designs.
Other changes include a less modern canopy from a MiG-21 (I think it comes from an Academy MiG-21F kit), which was more tricky to fit onto the original F-16 canopy than the LERX stuff. The F-16 canopy looked just too modern for my taste. An old Airfix pilot figure was added, too.
Another new feature is a new jet pipe, a J-79 nozzle from an Italeri Kfir that fits perfectly into the rear fuselage, and the fin. The latter was taken as a leftover part from my recent CF-151A project and comes from a 1:144 scale Tu-22M bomber (Dragon). It's higher, but less deep, and I thought that a slightly different shape and more area would be suitable for an attack aircraft. For the same reason the single, foldable stabilizer fin under the rear fuselage was replaced by two fixed strakes (from the F-16). Small details, but they change the look and make the aircraft appear more simple.
The landing gear was taken from the MiG-27, the front wheel strut had to be slightly shortened due to the reduced wheelbase on the Q-6.
The ordnance was puzzled together – according to current BAF weapons in use. I went for unguided missiles (taken from the Academy MiG-27 donation kit) and some 100kg iron bombs, leftover from a Trumpeter Il-28 bomber kit. These were arranged under the wing roots on improvised tandem MERs.
I did not even try to engrave new panel lines on the new front section - actually, almost the whole upper surface is featureless since it was made with putty. But bot 2C and NC putty are pretty touchy to drilling or engraving (as the rather fruitless attempt to drill open cavities for the two guns proved...), so I decided to just use paint effects.